Filter
Top Products
5-3
Rev 4 Aug/2007
KMD 250 Pilot's Guide
Section 5
System Messages
The following table describes the possible system messages:
System Messages
Message Text Description
All User Settings Cleared To
Defaults
This message indicates that a problem was detected in the internal
memory storage for user preference settings. All settings have been
reset to their factory defaults.
Data Card Has Expired
Unable To Receive FIS Data
(VDL Only)
The data card contains information required for receiving FIS information.
The data card has expired and FIS information will no longer be avail-
able. Go to www.bendixking.com and order a data card update.
Data Card Update Required
For Continued Reception Of
FIS Data (VDL Only)
The data card contains information required for receiving FIS information.
If the data card is not updated soon, then FIS information will no longer
be available. Go to www.bendixking.com and order a data card update.
Duplicate User Waypoint In
Flight Plan Data
This message occurs if more than one user waypoint have the same
identifier. This usually means that the flight plan and user data file on
the datacard have been modified incorrectly. Check the flight plans to
make sure the waypoints in them are correct. Edit if necessary.
Error In Flight Plan File An error has occurred while reading the flight plan data from the data-
card. This usually means the flight plan file on the datacard has been
modified incorrectly. Check the flight plans to make sure the waypoints
in them are correct. Edit if necessary. It message persists after
repeated power cycles, replace the datacard.
Error Writing Flight Plan
Data To Datacard
An error has occurred when the flight plan data was being stored on the
datacard. This may indicate a faulty datacard. If the error persists,
replace the datacard.
FIS Data Not Received For
More Than 15 Minutes
The KMD 250 has previously received FIS data, but it has been over 15
minutes since the last reception. This is most likely due to the aircraft
being at an altitude or location outside of FIS network coverage. See the
FIS Network Status Page for locations of FIS transmitters and status.
FIS Decryption Processor
Error. FIS Data May Be
Unavailable (VDL Only)
The KMD 250 is unable to decrypt the FIS data due to FIS Decryption
Processor Error.
FIS Receiver Failure The KMD 250 is unable to communicate with the KDR 510 VDL Receiver
or the KDR 610 XM Receiver. If this message persists, it may indicate a
problem with the Receiver or a wiring problem between the KDR 510/610
and KMD 250.
FIS Subscription Database
Error. Update Data Card To
Receive FIS Data (VDL
Only)
This message occurs when an error is detected in the FIS Subscription
Data on the datacard. This usually means that the datacard is out of date
and needs to be updated in order to receive FIS data.
FIS Subscription Will Expire
Soon (VDL Only)
This message occurs when at least one FIS subscription is about to
expire. Check the subscription status on the Aux FIS Subscription page.
Go to www.bendixking.com to purchase a new subscription.
Flight Plan Waypoint(s) Not
Found In Database Have
Been Deleted
This message will be displayed if an invalid waypoint is found in a flight
plan. This usually means the flight plan file on the datacard has been
modified incorrectly. Check the flight plans to make sure the waypoints
in them are correct. Edit if necessary.
Inside SUA This message is displayed when the aircraft is within Special Use
Airspace. Alerting must be enabled on Navigation Setup Page.
Internal GPS Failure This message is displayed if the internal GPS receiver (if so equipped)
has failed. Turn the KMD 250 off and then back on. If the message
persists, the unit may need service.
Internal Temperature Has
Exceeded Limits. Turn Unit
Off
This message appears when the KMD 250 unit temperature is too high.
Turn the unit off to allow it to cool down. This may indicate that the airflow
around the KMD 250 has been blocked.
Invalid User Waypoint In
Flight Plan Data
Indicates that an invalid user waypoint is found in a flight plan. This
usually means the flight plan file on the datacard has been modified
incorrectly. Check flight plans to make sure the waypoints in them are
correct. Edit if necessary. If the error persists, replace the datacard.
Messages 8/13/07 10:01 AM Page 5-3