Filter
Top Products
69
Basics
Section
Selecting a Zone opens the MKB Transmit
screen. You may want to select a sub screen to
set up a Zone using the [PAGE] knob. But you
first specify basic items in the MKB Transmit
screen, such as MIDI transmit channel, enabling
or disabling MIDI output to the internal tone
generator and to the MIDI OUT connector.
5Set MIDI transmit channel (TrnsCh) to “Ch01”
using the Knob [C]. Set MIDI output to the
internal tone generator (TG) and MIDI OUT
(MIDI) both to “on.”
These settings can differentiate each Zone from
one another, to internally or externally output
performance made in each Zone using a
separate MIDI channel. Finally, you will
separately control sound tones from four zones.
To do this, set “Ch01” to “Ch04” respectively to
the “TrnsCh” parameters in the MKB Transmit
screens for Zones 1 to 4. For the “TG” and
“MIDI” parameters, set both “on” for Zones 1
to 3. For Zone 4, set “off” to “TG” and “on” to
“MIDI.” You can switch between multiple
MKB Transmit screens using the Knob [A].
Some of basic settings for four zones are now
complete.
6Select “Zone01” again using the Knob [A].
Open the MKB Note screen using the [PAGE]
knob. In this screen, you can specify a key
range for a Zone.
In the MKB Note screen, you can also find other
parameters such as Note Limit, Transpose, etc.
Refer to Page 138 for more information about
these parameters.
7Set “Note Limit” (zone key range) with the
lowest and highest notes using Knobs [1]
(lowest) and [2] (highest). For “Zone01”, select
“C-2” for the lowest note and “B1” for the
highest.
8Use the Knob [A] to switch to the MKB Note
screen for “Zone02”. As in the same manner in
step 7, select “C2” for the lowest note and
“B2” for the highest.
9Use again the Knob [A] to switch to the MKB
Note screen for “Zone03”. As in the same
manner in step 7, select “C3” for the lowest
note and “G8” for the highest.
)Use the Knob one more time [A] to switch to
the MKB Note screen for “Zone04”. As in the
same manner in step 7, select “C3” for the
lowest note and “G8” for the highest. Note
that this key range setting will make a
overlapped range with Zone 3.
For detailed settings of a Zone, refer to Page 137.
MKBíNote)Octave Transpose Note Limit
Zone01 +1 +11 C-2 - G 8
!Turn the Knob [A] and select a Part for a Zone.
In this example, we select Phrase Clip Part for
Zone 1, Part 2 and Part 3 respectively for Zone
2 and Zone 3. We don’t select any internal Part
for Zone 4 since Zone 4 is set only to output
performance information via the MIDI OUT
connector. First, select Phrase Clip Part
(PartCL) for Zone 1.
You can also use the MEMORY or
PROGRAM/PART keys to select a Part for a
Zone (Page 119).
@Use the [PAGE] knob and open the MIX Kit
screen, to set up a Clip Kit for performance
using Phrase Clips.
A necessary Phrase Clip Kit should be prepared
in Phrase Clip Mode before you use in this setting
in Performance Mode.
#Use the [PAGE] knob and open the Layer Mode
(LYR Mode) screen. Set Layer Switch (Layer)
to “off,” MIDI receive channel (RcvCh) to “1.”
With settings made in steps ! to #, you can
now play Phrase Clips from the Clip Kit
assigned to “PartCL” (Phrase Clip Part) set to
MIDI receive channel 1 (RcvCh) when you
play in the key range of Zone 1.
$As in the same manner in steps ! to #, set up for
Zone 2. Turn the Knob [A] and select “Part02”.
Next go to the MIX Vce (Mix Voice) screen using
the [PAGE] knob, and select a Voice for
Arpeggiator. Then, use the [PAGE] knob to open
the LYR Mode (Layer Mode) screen and set RcvCh
(MIDI receive channel) to “2”. Also in this screen,
set the “Arp” switch to “on” for Arpeggiator
performance. Finally in the ARP Type (Arpeggio
Type) screen, set the Switch parameter to “on”.
With settings made here, you can now play with
Arpeggiator using a Voice assigned to “Part02”
set to MIDI receive channel 2 (RcvCh) when
you play in the key range of Zone 2.
%As in the same manner in steps ! to #, set up
for Zone 3. Turn the Knob [A] and select
“Part03”. Next go to the MIX Vce (Mix Voice)
screen using the [PAGE] knob, and select a
Voice for manual solo performance. Then, use
the [PAGE] knob to open the LYR Mode (Layer
Mode) screen and set the RcvCh (MIDI receive
channel) to “3”.
With settings made here, you can now play solo
using a Voice assigned to “Part03” set to MIDI
receive channel 3 (RcvCh) when you play in
the key range of Zone 3.
LYRíMode) Arp Layer RcvCh
PartCL on off 1
MIXíKit) Number
PartCL 001(A01)[Dr:Clip Kit]