Filter
Top Products
124
Performance Mode
■ Point
When the Mode (see earlier) has been set to “split,”
this sets the split point. The actual note of the split
point will be assigned to the upper section.
You can also select the split point by pressing the note
while holding down the [SHIFT] key.
❏ Settings: C-2 ~ G8
Master Keyboard settings (for split/layer)
For more information about Master Keyboard Mode,
refer to page 67.
Common Quick Edit
You can set various parameters governing the sonic
properties of the Layer Part, and many can be edited
using the Sound Control knobs on the front panel of
the CS6x. The following four screens are only
available when the Layer switch (Page 133) for each
Part is set to “on.”
QED Level (Quick Edit Level)
QED EF (Quick Edit Effect)
QED Filter (Quick Edit Filter)
QED EG (Quick Edit Envelope Generator)
Split Layer
Prameter Name
TrnsCh
TG
MIDI
Octave
Transpose
Note Limit Low
Note Limit High
Transmit Switch PB
Transmit Switch MW
Transmit Switch KnobA-C
Transmit Switch Knob1/2
Transmit Switch RB
Transmit Switch FC
Transmit Switch BC
Transmit Switch AT
Transmit Switch FS
Transmit Switch Sus
Transmit Switch Vol/FV
Transmit Switch Pan
Transmit Switch Bank Select
Transmit Switch Program Change
Transmit Preset Volume
Transmit Preset Pan
Transmit Preset Bank MSB
Transmit Preset Bank LSB
Transmit Preset PC
CS Control Number Assign
Zone1
ch
on
on
+0
+0
C-2
p
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone2
ch+1
on
on
+0
+0
p
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone3
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone4
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone1
ch
on
on
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone2
ch+1
on
on
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone3
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
Zone4
ch
off
off
+0
+0
C-2
G8
on
on
on
on
on
on
on
on
on
on
on
on
off
off
100
C
0
0
0
7
ch: Keyboard transmit channel
p: split point
Details about each parameter are given on page 137.
QED Level (Quick Edit Level)
You can set output level and pan parameters for each
Layer Part. The settings are also available in the Part
Edit screens.
■ Vol (Volume)
Set the output level of the Layer Part.
❏ Settings: 0 ~ 127
■ Pan
Set the stereo pan position of the Layer Part. You
can also adjust this parameter using the [PAN] knob
on the front panel of the CS6x.
❏ Settings: L63 (Left) ~ C (Center) ~ R63(Right)
■ RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Reverb
effect. You can also adjust this parameter using the
[REVERB] knob on the front panel of the CS6x.
❏ Settings: 0 ~ 127
■ ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Chorus
effect. You can also adjust this parameter using the
[CHORUS] knob on the front panel of the CS6x.
❏ Settings: 0 ~ 127
QED EF (Quick Edit Effect)
You can set the amount of Chorus applied to the Layer
Part, as well as Portamento settings.
■ Chorus
Set the Return level of the Chorus effect as an offset
value.
❏ Settings: -64 ~ 0 ~ +63
■ Portamento
Switch Portamento on or off. You can also set this
using the PORTAMENTO [ON/OFF] key on the
front panel of the CS6x.
❏ Settings: off, on
QEDíEF) Chorus Portamento-Time
Common -63 off 127
QEDíLevel) Vol Pan RevSend ChoSend
Common 127 C 63 63