Filter
Top Products
156
Phrase Clip Mode
■ Length
Set the Variation length ratio. You can change the
length of all the equal-sized sections by the amount
set here. If you select “toEnd,” the End Point of the
source Phrase Clip will be used as the End Point of
the Variation (after it has been divided).
❏ Settings: toEnd, 10 ~ 800%
If this setting is outside the End Point of the Phrase
Clip, it will be automatically limited to the End Point
setting.
PCLP VarAuto (Variation Auto-set)
The Start Point of the Variation is assigned
automatically. The Loop and End Points are the same
as those set in the original Phrase Clip.
There may be cases that automatic setting is not available
when the Clip has a narrow dynamic range (no big
difference between loudest and smallest volume levels)
because of the entire recorded level is too low, etc.
At this screen, Variation Set 1 to 8 are assigned to each
of the white notes of the keyboard in the range C3 to
C4. Press each note to switch to the respective
Variation Set, then set each Set’s parameters. Finally,
press the [ENTER] key to execute the Job.
If you are not satisfied with the result, try repeating the
process as you may get different results.
■ Threshold
Set the threshold level at which the Auto-set process
is started.
The Start Point is automatically set when the
average level of the Phrase Clip reaches or exceeds
this value.
❏ Settings: 0 ~ 255
■ Adjust
Set the amount by which the automatically-set Start
Point is adjusted (moved forward).
❏ Settings: -255 ~ 0
If the automatic setting is incorrect, Variation Set 1 will
be set such that the entire length of the Phrase Clip will
be played back. In this case the Start, Loop and End
Points for Variation Sets 2 to 8 will be set to zero.
PCLP VarRealTime (Variation Real-time)
You can set the Start Point of the Variation in real-time
while listening to the Loop. The Loop and End Points
remain in the same positions as set for the Phrase Clip.
The procedure is as follows.
PCLP VarRealTime) Hit[C3-C4] [EXIT]
Job C 2:001[SmplName] toVar1-8 toStop
PCLP VarAuto) Threshold Adjust
Job C 2:001[SmplName] 255 -255
1At this screen, you can play back the currently
selected Phrase Clip as a loop.
2Set the Start Points for Variations 1 to 8 by pressing
notes C3 to C4 on the keyboard.
By pressing the white notes (C3 to C4) on the
keyboard corresponding to Variation Sets 1 to 8, you
can set the Start Point while listening to the sound.
3In the same way, press the notes when setting the
Start Points for the other Variation Sets.
4When you press the [EXIT] key, you will see the
confirmation message. At this screen, you can verify
by playing Variation Sets 1 to 8 by pressing the white
notes on the keyboard between C3 and C4.
5Press the [INC/YES] key to set each Variation, or
press the [DEC/NO] key to cancel the operation and
return the Variation to its original state.
PCLP Var (Variation Manual)
You can change the settings for the Variation of the
currently selected Phrase Clip. Use Knob [A] to select
from Variation Sets 1 to 8 and use Knobs [B], [C], [1]
and [2] to set its parameters. Then press the [ENTER]
key to execute the Job.
At this screen, the white notes on the keyboard
between C3 and C4 can be used to select and play
Variation Sets 1 to 8.
■ Var (Variation Number)
Select the Variation you wish to set. The settings for
the selected Variation will be reflected in all
parameters.
❏ Settings: 1 ~ 8
■ Play (Play Mode)
Select the Phrase Clip playback mode. There are
three modes.
❏ Settings:
loop:
When you press a note on the keyboard, the Phrase Clip is
played completely from its Start Point. Then its looped
section is played back repetitively until you release the note.
oneshot:
When you press a note on the keyboard, the Phrase Clip is
played just once from its Start Point to its End Point (not
looped).
reverse:
When you press a note on the keyboard, the Phrase Clip is
played in reverse, just once, from its End Point to its Start
Point (not looped).
Basic details about each mode are given on Page 54.
PCLP Var) Play Start Loop End
Var=1: oneshot 2097150 2097150 2097150