Filter
Top Products
POSITION FILTER
No matter
what kind of
__________________
radionavigation
input
you're
using
with the
GlobalMap 1000, ___________________
"jitter"
orsmall
position
changes
______________ ______
will show on the
display
even
when
you're
not
moving.
For
______________________________
example,
the GPS module or
_____
____
antenna is mounted
high
above
the
deck, position changes
will
______________________________
occur
as the boat rolls in the
____________________________
waves.
The
position
filter will
average
the
jitter, showing
a smoother
position
and
navigation display.
(The jitter
affects not
only
the
position,
but all other
displays including
course over
ground
and
speed
over
ground.)
There arethree
settings:
off,
low,
and
high.
When the
GlobalMap
1000 is firstturned on or is
preset,
the
filter is turned
off. To set the
filter,
press
the MENU
key
twice. The screen
shown above
appears.
Now
press
the
key
next to the "Filter" label until the
check mark is on the desired
setting.
Press
the CLR
key
to exit this screen
and
put your change
into
effect.
PRESET
The
preset
feature returns all of the
GlobalMap's
settings
to their
original
factorysettings.
This resetsthe units of
measure, speakervolume, display
contrast,
and more.
However,
this doesn't
erase
any
event
markers,
waypoints
or routes.
To
preset
the
unit, press
the MENU
key
two times. The screen shown
above
appears.
Now
press
the
key
next to the °PresetUnit to
Factory
Settings"
label. A
message appears, warning you
that this will
preset
the
unit. Press the ENT to
preset
the unit or the CLR
key
to exit without
presetting.
If
you
press
the ENT
key,
the menu screen
disappears
and the
GlobalMap
1000 returns to the
mapping
screen. All units will be returned
to their
factory settings.
SIMULATOR
The
GlobalMap
1000 has a simulator feature that shows
your present
position
travelling
a
preset
course from
Miami,
Florida. All
navigation
features
of the unit
operate,
also. A
recurring message appears alerting
you
that the simulator
mode is enabled. DON'T USE THIS UNIT FOR
NAVIGATION
WHEN
THE SIMULATOR
IS OPERATING!
POWER CONNECTIONS
The
GlobalMap
1000 worksfrom atwelve-volt
batterysystem.
Forthe best
results,
attach the
power
cable
directly
to the
battery.
You can attach the
power
cable
to an
accessory
or
power
buss,
however
you may
have
problems
with electrical interference.
Therefore,
it's saferto
go
ahead and
attach the
powercable directlyto
the
battery.
If the cable istoo
short,
splice
#18
gauge
wire onto it. The
power
cable has
four
wires; red, black,
green,
and white. Red is the
positive
lead,
black is
negative
or
ground.
Make
certain to attach the in-line fuse holderto
the red lead as closeto the
power
source as
possible.
For
example,
if
you
have to
extend the
power
cable to
the
battery
or
power
buss,
attach one end
of the fuse holder
directly
to the
battery
or
power
buss. This will
protect
both the
unit and the
power
cable
in the event of a short. The
GlobalMap
1000 uses
a
3-amp
fuse.
IMPORTANT!
Do not use this
product
without a
3-amp
fuse wired into the
power
cable!
Failure to
use a
3-amp
fuse will void
your warranty.
TO
NMEA 0183
VERSION 2.0
INTERFACE
TO
LOW RAN c F
GPS MODULE
TO P' CONNECTOR
ON GLOBALMAP 1000
TO
NMEA 0180 or
0183
58
3
Customtize Display
a-
Units Of fleasure
)attut
Translations
Filter
10FF
OLOW a
High
Sinulator a ON 10FF
Preset Unit To
Factory Settings
—
a
More
VERSION 1.5
INTER FACE
GlobalMap
1000
POWER CONNECTIONS
PDF compression, OCR, web-optimization with CVISION's PdfCompressor