Filter
Top Products
34
DCM-2 HART INTERFACE Communication
* THIS VALUE CAN BE EDITED
** INDICATES AN ACTION RATHER THAN THE VIEWING OR EDITING
OF A PARAMETER
THIS IS THE MENU DISPLAYED BY THE HART COMMUNICATOR
AT POWER UP IF COMMUNICATION IS ESTABLISHED
THIS AND OTHER OFFLINE MENUS ARE COMMON TO ALL
HART COMMUNICATOR APPLICATIONS - MANY SUBMENUS EXIST
(1)
(2)
1
BLOCK REFERENCE NUMBERS APPEAR AT THE
UPPER RIGHT CORNER OF EACH BLOCK.
Online (1)
1 Functions
2 Position 45.4%
3 Demand 45.4%
4 Loop(Dem) 11.29 mA
5 Trq/Thrust 3%
6 Temp 73 degF
7 Feedback 11.30 mA
2
Functions
1 Setup Checklist
2 Device Information
3 Configuration
4 Statistics
5 Manual Operation
6 Diagnostics
7 Calibration Trim
3A
Setup Checklist
1 Drive S/N*
2 Drive Dir* CW Incr
3 Feedback* Enabled
4 CPS Zero%* 1.000 v
5 PositionUnit* deg
6 MaxTravel* 100 deg
7 Travel* 100 deg
8 DemRngLwr* 4.00 mA
9 DemRngUpr* 20.00 mA
Dem Curve* Linear
•
•
•
Alarm Mask 0xffffffff
4B
General Setup
1 Drive Dir* CW Incr
2 MaxTravel* 100 deg
3 Travel* 100 deg
4 StepSize* 0.100%
5 Stall Time* 300 S
6 StallProt* Enabled
7 LimitSwitch* Accept
8 PositionUnit* deg
9 Temperature Unit* degF
4C
PositionSensrSetup
1 Set Pos 0%**
2 Set Pos 100%**
3 PresCPS V 2.816 v
4 CPS Zero%* 1.000 v
5 CPS Span 4.000 v
6 CPS RngLwr 1.000 v
7 CPS RngUpr 5.000 v
8 Pos S/N* 454
9 Snsr Dir CW Incr
4D
Demand Setup
1 DemRngLwr * 4.00 mA
2 DemRngUpr * 20.00 mA
3 Dem Curve* Linear
4 Dem Curve Spcl
5 LOS Mode* Stay
6 LOS Pos* 50.00 %
7 DemLimLwr* 3.20 mA
8 DemLimUpr 22.00 mA
4E
Feedback Setup
1 FB RngLwr* 4.00 mA
2 FB RngUpr* 20.00 mA
3 Feedback* Enabled
4 FB Curve* Linear
4F
Torque Setup
1 Trq/Thrust* Enabled
2 Ovt Prot* Enabled
3 ShutDwnTrq* 150
4 Trq Null* 163 TK
5 Trq Const* 279 TK
4G
Op Mode
Follow*
Hold*
RunCW*
RunCCW*
Stay
Stop*
4H
Status
1 LED Status
2 Operating Status
3 Switch Status
4 Local Cntrl Status
5 Line Freq
6 CW Inhibitors
7 CCW Inhibitors
4I
4J
CW Torque
1 Segment 1 0 %
2 Segment 2 12 %
•
•
•
Segment 10 66 %
4K
CCW Torque
1 Segment 1 5 %
2 Segment 2 6 %
•
•
•
Segment 10 62 %
4L
Alarm Setup
1 AlarmPol* Drops Out
2 Alarm Mask*
4M
RealTimeClock
1 RTC Day* 8
2 RTC Month* 1
3 RTC Year* 2006
4 Hour (24)* 8
5 Minute* 5
4A
Review (3)
3B
Device Information
1 Tag* BECK2006
2 Descriptor*
3 Message*
4 Model# 11-159
5 Drive S/N*
6 Instld* 23/05/2006
7 Setup* 23/05/2006
8 Calbrtd* 28/05/2006
9 Review
Poll addr* 0
3C
3D
Statistics
1 Starts 485213
2 Reversals 242606
3 Stalls 0
4 OverTorques 14
5 Pk Torque 127%
6 TotRunTm 53268 S
7 High Temp 155 degF
8 Low Temp 23 degF
3E
3F
Diagnostics
1 Status
2 Tests
3 CW Torque
4 CCW Torque
5 Alarm Setup
6 RealTimeClock
3G
Calibration Trim
1 PresCPS V* 2.816 v
2 Loop(Dem)* 11.29 mA
3 Feedback* 11.29 mA
4 Trq/Thrust* 3 %
5A
Dem Curve Spcl
1 DemNode1X 0 %
2 DemNode1Y 0 %
3 DemNode2X 5 %
4 DemNode2Y 5 %
•
•
•
DemNode21X 100 %
DemNode21Y 100 %
5B
LED Status
Status OFF
Reverse OFF
Forward OFF
Demand OFF
Position OFF
Trq/Thrust OFF
Stall OFF
Temperature OFF
FB Open OFF
Limit OFF
Acknowledge OFF
5C
Operating Status
Dem <> Limits OFF
Pos <> Limits OFF
Temp <> Limits OFF
Torq <> Limits OFF
Over Torq Stop OFF
Stalled OFF
Feedback Open OFF
Switch Block OFF
5D
Switch Status
LV Lim CCW OFF
LV Lim CW OFF
OvrRd CCW OFF
OvrRd CW OFF
OvrRd Stop OFF
HndSw CCW OFF
HndSw CW OFF
HndSw AUTO OFF
5E
Local Cntrl Status
Calibrate OFF
Set Pos 100% OFF
Set Pos 0% OFF
Set Dem 100% OFF
Set Dem 0% OFF
5F
CW Inhibitors
Balance ON
Supervisory OFF
Stall OFF
OverTrq/Thr OFF
Switch Block OFF
Bad Pos Sig OFF
Bad Dem Sig OFF
Local Cal OFF
5G
CCW Inhibitors
Balance ON
Supervisory OFF
Stall OFF
OverTrq/Thr OFF
Switch Block OFF
Bad Pos Sig OFF
Bad Dem Sig OFF
Local Cal OFF
5H
Alarm Mask
DemandLOS ON
Trq/Thrust High ON
Stall ON
Trq/Thrust Stop ON
Stop/Limit ON
FeedbackLOS ON
Temperature ON
PositionLOS ON
RTC Fail ON
Torq/Thrust/MeasFail
PositionA/D Error
DemandMeasFail ON
Reserved 1 ON
PositionLOS ON
TemperatureMeasFail
MemoryFail ON
InvalButtonPress ON
DemandTooHigh ON
DemUnderHART/FF Ctl ON
DemUnderPAT Ctl ON
(3) PROVIDES AN EXTENDED LIST OF DRIVE PARAMETERS
Tests
1 FB Out Test**
2 Board Self-Test**
3 Identify Device**
4 Board Reset**
Configuration
1 General Setup
2 PositionSensrSetup
3 Demand Setup
4 Feedback Setup
5 Torque Setup
6 Restore to Factory**
7 Use Default Setup**
Manual Operation
1 Op Mode* Follow
2 Demand* 45.3%
3 Reset Stall**
Figure 1
BECK-MK2 HART COMMUNICATOR MENUS FOR THE DCM-2