Filter
Top Products
CONTROL MODULE PIN OUT INFORMATION
AIRBAG I SRS CONTROL MODULE
‘;7 Pin
Description
I FC29.4
GROUND
0
FC29.5
MAJOR INSTRUMENT PACK AIRBAG MIL
D
FC29.6
SERIAL COMMUNiCATlDN
I FCZ9.7
IGNITION SWITCHED POWER SUPPLY
I FCZ9-8
LH IMPACTSENSOR GROUND SUPPLY STATUS
I FC29-9
RH IMPACTSENSOR GROUND SUPPLY STATUS
I FC29-71
LH IMPACT SENSOR STATUS
I FCZ9~12
RH IMPACT SENSOR STATUS
DRIVER SIDE AIRBAG POWER SUPPLY
DRIVER SIDE AIRBAG GROUND SUPPLY
PASSENGER SIDE AlRBAG GROUND SUPPLY
PASSENGER SIDE AIRBAG POWER SUPPLY
FUSED SUPPLY INTERRUPT
DEPLOYMENT BATERY POWER SUPPLY
COMMON AIRBAG GROUND SUPPLY
COMMON AIRBAG GROUND SUPPLY
CODE RETRIEVAL PULSED OUTPUT
GROUND
Active
GROUND
GROUND
Inactive
GROUND
B-
BA
0 v (NO FAULTj
GROUND ,NO FAULT,
GROUND ISHORTED,
GROUND (SHORTED)
GROUND
B*
Bi
BA (SHORTED SAFING SENSOR,
OPEN CIRCUIT
GROUND iSHORTED IMPACT SENSOR,
OPEN CIRCUIT
GROUND iSHORTED lMPACTSENSORi
OPEN CIRCUIT
B- ,SHORTED SAFlNG SENSOR
OPEN CIRCUIT
GROUND (FAULT PRESENT,
BT iN0 FAULT,
B,
B-
GROUND WORTED IMPACT SENSOR)
OPEN CIRCUIT
GROUND iSHORTED IMPACT SENSORI
OPEN CIRCUIT
GROUND IPVLSED,
B+
GROUND
GROUND
COMPONENTS
Component
Connector I Type
I
Color
ARBAG -DRIVER SIDE (STEERING WHEEL)
AiRBAG -PASSENGER SIDE
AIRBAG INTERROGATlON CONNECTOR
NRBAG, SK CONTROL MODULE
IMPACT SENSOR - RH
iMPACT SENSOR LH
SW, 1, S-WAY EPC , BLACK
RX74 i S-WAY EPC i BLACK
FC40 !bWAY MULTILOCK 070 /WHITE
FC29 : 12.WAY FORD CARD 1 BLACK
FC30,12-WAY FORD CARD 1 GREY
LF51 I&WAY FORD CARD, NATURAL
LF50 ‘d-WAY FORD CARD. NATUFtAL
HARNESS-TO-HARNESS CONNECTORS
Connector
Type
I
Color
Location / Access
LF2
SW?0
B-WAY FORD CARD I BLACK
Z-WAY EPC BLACK
LEFT HAND ‘!4 POST CONNECTOR MO”NTlNG BRACKET I ‘A’ POST TRlM
INSlDE STEERING COLUMN COWL
Location I Access
CENTER OF STEERING WHEEL
LEFT HAND SIDE OF AIRBAG ASSEMBLY
RIGHT HAND’A’POST:‘N POSTTRIM
RIGHT HAND ‘A’ POST,‘K POSTTRIM
FRONT UPPER moss MEMBER I FowwARD OF RADIATOR
FRONT UPPER CROSS MEMBER I FORWARD OF RADIATOR
GROUNDS
Ground
Location / Type
FClS
EYELET iSINGLE lTRANSMlSSlON TUNNEL, RIGHT HAND SIDE
CONTROL MODULE PIN OUT INFORMATION (FOLD OUT PAGE)
The following symbols are used to represent
values
for Control Module Pin Out data:
I
Input
D
Serial and encoded communications
0 output
B+ Battery voltage
KHz Frequency x 1000
C CAN (Network)
MS Milliseconds
SG Signal Ground
V Voltage (DC)
S SCP Network
Hz Frequency
MV Millivolts
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all
components connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
REFER TO THE FRONT OF THE BOOK FOR ILLUSTRATIONS DETAILING THE LOCATION AND
IDENTlFlCATlON
OF COMPONENTS, RELAYS,
CONNECTORS, HARNESSES, GROUNDS, VEHICLE CONTROL MODULES AND CONTROL MODULE PINS.
DATE OF ISSUE: FEBRUARY 1998