Filter
Top Products
E-SERIES (May, 2004)20
E-SERIES (May, 2004) 21
STATEMENTS OF CONFORMITY
111 The statements below are applicable to the following
incomplete vehicle type when equipped with a at
glass mirror on the passenger-side:
• Incomplete E-Series Van
This vehicle, when completed, will conform to Standard
111, Rearview Mirrors, if:
• The mirrors and their mounts as supplied by Ford
Motor Company are not removed, relocated, replaced,
or altered.
• No structural modifications are made to the body
which would affect the stability of the mirror mounts.
• Any modications or additions made to the incomplete
vehicle must not adversely affect the driver’s view
to the rear in the outside mirrors along both sides
of the vehicle.
113 The statement below is applicable to all incomplete
vehicle types except the Basic (Stripped) Chassis:
This vehicle, when completed, will conform to Standard
113, Hood Latch Systems, if the hood latch system
as provided by Ford Motor Company is not removed
or altered.
113 The statement below is applicable to the following
incomplete vehicle type:
• E-Series Basic (Stripped) Chassis
Conformity with Standard 113, Hood Latch Systems, is
not substantially affected by the design of this incomplete
vehicle; accordingly Ford Motor Company makes no
representation as to conformity with this Standard.
114 The statements below are applicable to all incomplete
vehicle types except the Basic (Stripped) Chassis
when completed as either a MPV or a Truck with a
GVWR of 4536 kg [10,000 lb] or less:
This vehicle, when completed, will conform to Standard
114, Theft Protection, if the following components, to
the extent provided by Ford Motor Company, are not
removed, relocated, altered, or modied in any way:
• Steering column locking mechanism system
• Ignition key/transmission shift interlock locking
system
• Ignition key-locking system
• Key warning buzzer system
If any of the above components are added to the
vehicle they must conform to the requirements of this
Standard.
114 The statement below is applicable to the following
incomplete vehicle type:
• E-Series Basic (Stripped) Chassis
The Basic (Stripped) Chassis is designed by Ford
Motor Company to be completed as a walk-in van type
vehicle. Walk-in vans are exempt from the requirements
of Standard 114, Theft Protection. See walk-in van
denition, on page 5.
115 Canadian Requirements:
The statements for Part 565.4 are appropriate
compliance representations for CMVSS 115, Vehicle
Identication Number, if this incomplete vehicle was
manufactured for sale or use in Canada.
116 The statement below is applicable to all incomplete
vehicle types:
This vehicle, when completed, will conform to Standard
116, Motor Vehicle Brake Fluids, so long as any
brake uid added or replaced conforms to the DOT 3
specications of the standard and contaminants are not
introduced into the hydraulic brake system.
118 The statement below is applicable to all incomplete
vehicle types not equipped with power windows when
completed as either a MPV or a Truck with a GVWR of
4536 kg [10,000 lb] or less:
Conformity with Standard 118, Power Operated
Window, Partition, and Roof Panel Systems, is not
substantially affected by the design of this incomplete
vehicle; accordingly, Ford Motor Company makes no
representation as to conformity with this Standard. If any
power operated window, partition, or roof panel systems
are installed by subsequent stage manufacturers, they
must conform to the requirements of Standard 118.
118 The statement below is applicable to all incomplete
vehicle types equipped with power windows when
completed as either a MPV or a Truck with a GVWR of
4536 kg [10,000 lb] or less:
This vehicle, when completed, will conform to Standard
118, Power Operated Window, Partition, and Roof Panel
Systems, if the power operated windows, motors, wiring,
and key and switch activation systems, where provided
by Ford Motor Company, are not removed, relocated,
altered, or modified in any way. If additional power
operated window, partition, or roof panel systems are
installed by subsequent stage manufacturers, they must
conform to the requirements of Standard 118.
119 The statement below is applicable to all incomplete
vehicle types:
All tires supplied by Ford Motor Company are in full
conformity with Standard 119, New Pneumatic Tires for
Vehicles Other than Passenger Cars.
If additional tires are installed or the existing tires are
replaced by subsequent stage manufacturers, they must
conform to the requirements of Standard 119.
120 The statement below is applicable to all incomplete
vehicles except for the Basic (Stripped) Chassis:
This vehicle, when completed, will conform to the tire
and rim selection requirements of Standard 120, Tire
Selection and Rims for Motor Vehicles Other Than
Passenger Cars, if the tire and rim assemblies and the
Incomplete Vehicle Label that is afxed to the vehicle
are not removed, altered, or replaced.
120 The statements below are applicable to the following
incomplete vehicle type:
• E-Series Basic (Stripped) Chassis
This vehicle, when completed, will conform to the tire
and rim selection requirements of Standard 120, Tire
Selection and Rims for Motor Vehicles Other Than
Passenger Cars, if:
• The tire and rim assemblies, are not removed, altered,
or replaced.
• The nal stage manufacturer must, in accordance
with the requirements of Standard 120 and Part
567 of Title 49 Code of Federal Regulations, afx a
label to the completed vehicle indicating tire size,
rim size, cold ination pressure, and the gross axle
weight ratings. This information is provided on the
label that is afxed to the cover of this manual for
E-Series vehicles.