Filter
Top Products
E-SERIES (May, 2004)18
E-SERIES (May, 2004) 19
STATEMENTS OF CONFORMITY
108 The statements below are applicable to the following
incomplete vehicle type:
• Cutaway
This vehicle, when completed, will conform to Standard
108, Lamps, Reflective Devices, and Associated
Equipment, if all the required lighting equipment as
indicated in Table G on this page (identied by the codes
D, R and S) is designed and installed in accordance with
the requirements of Standard 108 and the directions
contained in this statement. Additionally, if the completed
vehicle overall length is 9.14 meters [30 feet] or more,
intermediate side marker lamps and reex reectors
(not supplied by Ford Motor Company) are also required
for compliance with Standard 108.
The items of equipment which are supplied by Ford
Motor Company (identied by the code S in Table G,
on this page) are designed and installed to conform to
all the requirements of Standard 108. The completed
vehicle will conform with these components if the
subsequent stage manufacturer does not remove,
relocate, alter, or modify such equipment or modify the
power supply or wiring to such equipment, and does
not complete the body in such a conguration as to
impair the visibility and conformity to the photometric
requirements of the installed lamps and reflective
devices.
Specific requirements for lighting and associated
equipment are listed by incomplete vehicle type in Table
G on this page.
Lamps, reective devices, and associated equipment
necessary to complete the vehicle from an incomplete
vehicle must conform to the equipment, locations,
special wiring, visibility, photometric, and performance
requirements of Standard 108 and to the applicable
SAE standards or recommended practices referenced
or sub-referenced in this Standard.
All electrical equipment added to the vehicle by
subsequent stage manufacturers must conform to the
wiring practices set forth in the Electrical Wiring Section
of the Ford Truck Body Builders Layout Book.
108 The statements below are applicable to the following
incomplete vehicle types:
• Incomplete E-Series Van or Wagon
This vehicle, when completed, will conform to Standard
108, Lamps, Reflective Devices, and Associated
Equipment, if the subsequent stage manufacturer does
not:
• Remove, alter, replace, or relocate the lighting
equipment installed on the incomplete vehicle
• Modify the power supply or wiring to such equipment
• Add any additional external lighting equipment
• Increase the overall width of the vehicle beyond that
of the incomplete vehicle
• Complete, modify, or add components to the vehicle in
such a manner as to impair the visibility and conformity
to the photometric requirements of the installed lamps
and reective devices
108 (Continued Next Page)
TABLE G
Standard 108 Lighting Equipment
E-Series
Completed
as Truck,
MPV, Bus or
School Bus
Headlamps S S
Tail Lamps R/D R/D
Stop Lamps R/D R/D
Center High Mounted
Stop Lamp (CHMSL) R N
License Plate Lamps R/D R/D
Reex Reectors – Side Front S S
– Side Rear R R
– Rear R R
Side Marker Lamps – Front S S
– Rear R R
Back-Up Lamps R/D R/D
Turn Signal Lamps – Front S S
– Rear R/D R/D
Turn Signal Operating Unit S S
Turn Signal Flasher (2) S S
Vehicular Hazard Warning Signal
Operating Unit S S
Vehicular Hazard Warning Signal
Flasher S S
Identication Lamps – Front N R
– Rear N R
Clearance Lamps – Front N R(1)
– Rear N R
Parking Lamps R N
School Bus Lamps and Switches R R
(School Bus except Multifunction
School Activity Bus)
S Required on completed vehicle and supplied with the
incomplete vehicle.
R Required on completed vehicle and not supplied with the
incomplete vehicle.
N Not required for completed vehicle.
D Required on completed vehicle and available as an option
(either on vehicle or shipped in dunnage).
(1) If a second unit body width is greater than 2032 mm [80 in] or
higher than the cutaway body, additional clearance lamps may
be required that comply with this standard.
(2) Designed for two turn signal lamps per vehicle side (one front
and rear). If additional lamps are required, replace the turn
signal asher with one having the correct lamp load rating.
Width less than
2032 mm [80 in]
Width 2032 mm
[80 in] or more
Item