Filter
Top Products
E-SERIES (May, 2004)18
E-SERIES (May, 2004) 19
STATEMENTS OF CONFORMITY
108 The statements below are applicable to the following
incomplete vehicle type:
• E-Series Basic (Stripped) Chassis:
Conformity with Standard 108, Lamps, Reflective
Devices, and Associated Equipment, is not substantially
affected by the design of this incomplete vehicle;
accordingly, Ford Motor Company makes no rep-
resentation as to conformity with this standard. However,
Ford Motor Company does represent that the items
of lighting equipment, when provided in the E-Series
dunnage box attached to the chassis, are designed to
conform to the requirements of Standard 108.
108 Canadian Requirements:
The preceding statements for Standard 108 are
appropriate compliance representations for CMVSS
108, Lighting, and CMVSS 108.1, Headlamps, if this
vehicle is manufactured for sale or use in Canada,
provided:
• No component of the Daytime Running Lamp (DRL)
system is removed, relocated, or modied.
110 U.S. Requirements:
The statement below is applicable to all incomplete
vehicles with a GVWR of 4536 kg [10,000 lbs] or
less:
This incomplete vehicle does not comply to FMVSS
110. In order to comply, the nal stage manufacturer
must afx a tire placard as specied in paragraph S4.3
of FMVSS 110. The decal must be afxed to the B-Pillar.
See below for placard content and note color and format
requirements in S4.3.
108 (Continued)
111 The statements below are applicable to the incomplete
E-Series Van with no driver-seat when equipped with
a convex mirror on the passenger-side:
This vehicle, when completed, will conform to Standard
111, Rearview Mirrors, if:
• The mirrors and their mounts as supplied by Ford
Motor Company, are not removed, relocated, replaced,
or altered.
• No structural modifications are made to the body
which would affect the stability of the mirror mounts.
• The Seating Reference Point (see definition on
page 5) and the seat back torso angle of the driver-
seat installed or completed by the subsequent stage
manufacturer are located as shown in Figure C
page 32 corresponding to the particular incomplete
vehicle type.
• Any modications or additions made to this incomplete
vehicle do not adversely affect the driver’s view to
the rear in the outside mirrors along both sides of
the vehicle.
If any alteration blocks the rear eld of view through the
inside mirror, Standard 111 may require that the vehicle
have a at glass on the passenger side.
111 The statement below is applicable to the following
incomplete vehicle types when not equipped with
outside mirrors:
• Cutaway
• E-Series Basic (Stripped) Chassis
• Incomplete E-Series Van
Conformity with Standard 111, Rearview Mirrors, is not
substantially affected by the design of this incomplete
vehicle; accordingly, Ford Motor Company makes no
representation as to conformity with this Standard.
111 The statements below are applicable to the Cutaway
when equipped with outside mirrors:
Conformity with the stability requirements of Standard
111, Rearview Mirrors, is not substantially affected
by the design of this incomplete vehicle; accordingly
Ford Motor Company makes no representation as to
conformity with stability requirements of this Standard.
However, except for the stability requirement, this
vehicle, when completed, will conform to Standard 111,
Rearview Mirrors, if:
• The outside mirrors and their mounts, as supplied
by Ford Motor Company, are installed in accordance
with the instructions that accompany them and they
are not relocated, replaced, or altered.
• The Cutaway with the School Bus Prep Package is
completed as a school bus and any outside mirrors
(not provided by Ford Motor Company) are installed
in conformity with the requirements of Standard 111
for school buses.
111 The statements below are applicable to the following
incomplete vehicle types when equipped with a driver
seat (including untrimmed seat) and a convex mirror
on the passenger-side:
• Incomplete E-Series Van or Wagon
This vehicle, when completed, will conform to Standard
111, Rearview Mirrors, if:
• The mirrors and their mounts as supplied by Ford
Motor Company are not removed, relocated, replaced,
or altered, except as noted below.
• No structural modifications are made to the body
which would affect the stability of the mirror mounts.
• Any modications or additions made to this incomplete
vehicle do not adversely affect the driver’s view to
the rear in the outside mirrors along both sides of
the vehicle.
• The driver-seat is not replaced, relocated, or modied
other than for the addition of seat trim.
If any alteration blocks the rear eld of view through the
inside mirror, Standard 111 may require that the vehicle
have a at glass mirror on the passenger side.