Filter
Top Products
i
TABLE OF CONTENTS
FOREWORD............................................ iii
SYSTEM CONFIGRATION ...................... iv
MENU TREE............................................. v
1. OPERATIONAL OVERVIEW
1.1 Control Description..........................1-1
1.2 Turning On and Off the Power .......1-2
1.3 Adjusting Display Contrast and
Brilliance..........................................1-3
1.4 Display Mode...................................1-3
1.5 Transmitting Data ............................1-6
1.6 The Interface Unit............................1-8
2. DISPLAY AND TRACK
2.1 Enlarging/Shrinking the Display ......2-1
2.2 Display Orientation ..........................2-1
2.3 The Cursor.......................................2-1
2.4 Shifting the Display..........................2-2
2.5 Centering Own Ship's Position........2-2
2.6 Stopping/Starting Plotting and
Recording of Track..........................2-2
2.7 Erasing Track...................................2-3
2.8 Track Plotting Interval......................2-4
2.9 Apportioning the Memory ................2-5
2.10 Bearing Reference ........................2-5
3. MARKS
3.1 Entering Marks ................................3-1
3.2 Erasing Marks..................................3-1
3.3 Mark Shape .....................................3-2
3.4 Connecting Marks............................3-2
3.5 Entering Event Marks......................3-2
3.6 Event Mark Shape...........................3-3
3.7 Entering the MOB Mark...................3-3
4. NAVIGATION PLANNING
4.1 Entering Waypoints .........................4-1
4.2 Editing Waypoints............................4-4
4.3 Erasing Waypoints...........................4-4
4.4 Entering Routes...............................4-5
4.5 Erasing Route Waypoints................4-6
4.6 Replacing Route Waypoints............4-7
4.7 Erasing Routes................................4-7
5. SETTING DESTINATION
5.1 Setting Destination ..........................5-1
5.2 Cancelling Destination.....................5-5
5.3 Erasing Route Waypoints (flags).....5-6
5.4 Finding Range and Bearing
Between Two Points........................5-7
6. SETTING UP VARIOUS DISPLAYS
6.1 The Data Display.............................6-1
6.2 Position Format ...............................6-2
6.3 Demo Display ..................................6-4
7. ALARMS
7.1 Overview..........................................7-1
7.2 Arrival Alarm, Anchor Watch Alarm..7-1
7.3 Cross Track Error (XTE) Alarm .......7-2
7.4 Speed Alarm ....................................7-3
7.5 Trip Alarm ........................................7-3
7.6 Water Temperature Alarm................7-4
7.7 Depth Alarm.....................................7-4
7.8 DGPS Alarm ....................................7-4
8. MENU SETTINGS
8.1 GPS SETUP Menu..........................8-1
8.2 Units of Measurement .....................8-4
8.3 Size and Brilliance of Markers.........8-5
8.4 Outputting Data ...............................8-6
8.5 Receiving Data from Personal
Computer.........................................8-8
8.6 DGPS Settings ...........................8-10
8.7 GPS Monitor Display.....................8-11
9. MAINTENANCE &
TROUBLESHOOTING
9.1 Clearing the Memory.......................9-1
9.2 Preventive Maintenance..................9-2
9.3 Error Messages ...............................9-2
9.4 Troubleshooting...............................9-4
9.5 Diagnostic Tests ..............................9-5
9.6 Interface Unit IF-2500......................9-6
10.1 INSTALLATION ............................10-1
10.1 General........................................10-1
10.2 Display Unit .................................10-2
10.3 Antenna Unit................................10-3
10.4 Wiring...........................................10-5
10.5 Initial Settings..............................10-6
10.6 Interface Unit IF-2500................10-14
APPENDIX ..........................................AP-1
WORLD TIME STANDARDS..............AP-1
GEODETIC CHART LIST...................AP-2
LORAN C CHAINS.............................AP-3
DECCA CHAINS.................................AP-4
PARTS LIST .......................................AP-5
PARTS LOCATION.............................AP-6
INTERFACE DOCUMENTATION.......AP-7