Filter
Top Products
Table of user-selectable features: 1 chirp = OFF, two chirps = ON
Feature Select
Column 1
1st latched
Column 2
2nd latched
Column 3
3rd latched
Column 4
4th latched
Column 5
5th latched
Column 6
6th latched
Row 1
1st momentary
Sound 1: on/off
info on page 26
Add new remote to channel 1
info on page 15 NOTE 1
AutoLock: on/off
info on page 25
AutoArming: on/off
info on page 18
NightVision: off/on but no
post-parking illumination/on
(1/2/3 chirps) info on page 23
Use this remote to activate which
memory seat position?
info on page 20 NOTE 6
Row 2
2nd momentary
Sound 2:
on
/off
info on page 26
Add new remote to channel 2
info on page 15 NOTE 1
AutoUnLock:
on
/off
info on page 25
AutoArm & Lock: on/
off
info on page 18
Post-parking and remote headlight
duration: 1sec–2.0min (30sec)
info on pages 15 and 23 NOTE 5
Door ajar warning
/delayed
courtesy lights
this feature is for installers only
Row 3
3rd momentary
Sound 3: on/off
info on page 26
Add new remote to channel 3
info on page 15 NOTE 1
FACT: on/off
info on page 23
15-second entry delay: on/off
info on page 18
SilentNight: on/off
info on page 23
RPM-activated AutoLock: on/off
info on page 25
Row 4
4th momentary
Sound 4: on/off
info on page 26
Add new remote to channel 4
info on page 15 NOTE 1
AutoActivate channel 4 timed
accessory upon remote arming
this feature is for installers only
AutoStart: battery mode/
temperature mode/dual mode/off
(2/3/4/1 chirps) NOTE 3
✱ Channel 4 timer: 1sec-2.0min
(30sec) info on page 15 NOTE 5
RPM programming
this feature is for installers only
Row 5
5th momentary
Sound 5:
on
/off
info on page 26
Add new remote to channel 5
info on page 15
NOTE 1
QuietChirps: on/
off
info on page 26
Siren duration: 60/
30
seconds
(1/
2
chirps) info on page 26
Channel 4 output type:
pulsed
/timed/latched
this feature is for installers only
Lock pulse duration: 3sec/
1sec
this feature is for installers only
Row 6
6th momentary
Sound 6: on/off
info on page 26
Erase all channels
info on page 26 NOTE 2
Long-term chirp silencing: on/off
info on page 26
Set a new secret valet code
info on page 20 NOTE 4
NOT USED
Diesel/gasoline fuel injection
this feature is for installers only
✱ WARNING: If the system automatically closes the power windows and sunroof when you remotely arm, DO NOT CHANGE THIS SETTING: It requires installer-only adjustment. Changing the duration may cause damage.
The gray cells indicate features that requires programming only by a qualified installer. DO NOT change installer-only settings — damage to the system or your vehicle may result.
38 39
© Copyright Clifford Electronics, Inc., 1997 31-708C/IPOM/797
NOTE 1: Transmit the appropriate channel of the new remote control. You will hear the
same number of chirps as the channel selected (e.g., 3 chirps for channel 3) to confirm
programming of that channel.
NOTE 2: When you hear one chirp, all remote control channels will have been erased
from the system memory. You must now add the new and/or existing remote controls
to the system (i.e., program channels 1–5 of each remote control).
NOTE 3: Press button 4 to turn AutoStart off (1-chirp confirmation), press button 1 to
select AutoStart battery mode (2-chirp confirmation), press button 2 to select AutoStart
temperature mode (3-chirp confirmation), press button 3 to select AutoStart dual mode
(4-chirp confirmation). This selects the AutoStart mode. To engage AutoStart, you will
later transmit channel 10 while the system is disarmed (see page 28 for more information).
NOTE 4: Immediately flip the switch to its latched position, then:
a. Enter the new code that you wish to use. The system will sound the same number
of chirps as the digit you choose when you move the switch to the latched side
(e.g., if the first digit is 4, you’ll hear four chirps when you press the latched side).
b. Make sure to return the switch to its center position when complete.
c. Wait 3 seconds until you hear 2 chirps, indicating the new code has been accepted.
d. Turn the ignition off. You’ll hear 3 chirps and the LED will turn off.
e.
VERY IMPORTANT:
You must immediately test your new valet code
: Turn
the ignition on, enter your new code, then flip the switch to its latched position.
The LED will illuminate. If it does not, the new code you programmed and the one
you just entered do not match. The system has reverted to the previous code.
NOTE 5: The timer starts as soon as you select this feature. When the duration you wish
has been reached, press remote control button 1. You’ll hear two chirps to confirm the
new duration.
NOTE 6: After you select this feature, take the remote control you will be using and
press either button 1, 2, 3 or 4 to select the vehicle’s memory seat position 1, 2, 3 or 4,
respectively, that has been set up for your driving comfort. For a second driver, select
this feature, take the other remote control and press either button 1, 2, 3 or 4 to select
the vehicle’s memory seat position 1, 2, 3 or 4, respectively, that has been set for the
secondary driver. You may do this with up to four different remote controls and up to
four different memory seat positions, in any combination.