Support User Manuals

Audiovox AS9233ST Automobile Alarm User Manual

Open as PDF

of 20

128-8605

4 of 20

4

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps

This Action Accesses Feature Bank 3 Remote Start Selectable Features

First Press the valet switch one time Non Functional On This Unit

or

Second Press and release the valet switch 2 chirps = RF start chirp on

Press transmitter Lock button to change 1 chirp = RF start chirp off

or

Third Press and release the valet switch 2 chirps = run time set for 10 mins

Press transmitter Lock button to change 3 chirps = run time set fro 15 mins

Press transmitter Lock button to change 4 chirps = run time set for 20 mins

Press transmitter Lock button to change 1 chirp = run time set for 5 mins

or

Fourth Press and release the valet switch 1 chirp = parking lights on steady w/RS active

Press transmitter Lock button to change 2 chirps = parking lights flashing w/RS active

or

Fifth Press and release the valet switch 2 chirps = tachometer input checking

Press transmitter Lock button to change 1 chirp = voltage sense input checking

or

Sixth Press and release the valet switch 1 chirp = greater than 0.5 V check before start

Press transmitter Lock button to change 2 chirps = less than 0.5 V check before start

or

Seventh Press and release the valet switch 2 chirps = ign 2 on during crank

Press transmitter Lock button to change 3 chirps = ign 2 same as accessory

Press transmitter Lock button to change 1 chirp = ign 2 off during crank

or

Eighth Press and release the valet switch Non Functional On This Unit

or

Ninth Press and release the valet switch 1 chirp = diagnostics off

Press transmitter Lock button to change 2 chirps = diagnostics on

or

Tenth Press and release the valet switch 2 chirps = crank time 1.0 sec

Press transmitter Lock button to change 3 chirps = crank time 1.5 sec

Press transmitter Lock button to change 4 chirps = crank time 2.0 sec

Press transmitter Lock button to change 1 chirp = crank time 0.8 sec

or

Eleventh Press and release the valet switch 1 chirp = unit set for gasoline engine

Press transmitter Lock button to change 2 chirps = unit set for diesel engine 10 sec delay

Press transmitter Lock button to change 3 chirps = unit set for diesel engine 15 sec delay

Press transmitter Lock button to change 4 chirps = unit set for diesel engine 20 sec delay

or

Twelfth Press and release the valet switch 1 chirp = transponder output while R/S active

Press transmitter Lock button to change 2 chirps = transponder output during start only

Press transmitter Lock button to change 3 chirps = transponder output until ignition turned off

or

Thirteenth Press and release the valet switch Non Functional On This Unit

or

Fourteenth Press and release the valet switch 1 chirp = crank averaging w/voltage input checking

Press transmitter Lock button to change 2 chirps = preset crank time w/voltage input check

Fifteenth Non Functional On This Unit

or

Sixteenth Press and release the valet switch Non Functional On This Unit

or

Seventeenth Press and release the valet switch 1 chirp = aux o/p Black/Blue single pulse

Press transmitter Lock button to change 2 chirps = aux o/p Black/Blue as alarm feature #1

Press and release the valet switch

or

Eighteenth Press and release the valet switch 1 chirp = Double pulse required on Blue/Black Start Input

Press transmitter Lock button to change 2 chirps = single pulse required on Blue/Black Start Input

or

Turn the ignition off to: Exit Programming Mode

Note: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

previous next