Filter
Top Products
A
P-1
APPENDIX
Menu Tree
The example screens shown in this manual may not match the screens you see on your
display. The screen you see depends on your system configuration and equipment settings.
MODE (
STANDARD
, MONITOR, SERVICE, DISABLE)
IP ADDRESS (
000.000.000.000 - 255.255.255.255;
172.031.024.001
)
SUB NET MASK (
000.000.000.000 - 255.255.255.255;
255.255.000.000
)
PORT NO. (0 -
65535;
10000
)
L/L, COG, SOG
HDG
ROT (Same choices and defaults as HDG)
[MENU] key
CREATE MSG
TX LOG
RX LOG
SET MSG TYPE
SET MSG
SEND MSG
ADRS TYPE (
BROAD CAST
, ADRS CAST)
MMSI
MSG TYPE (NORMAL,
SAFETY
)
CHANNEL (
ALTERNATE
, BOTH A & B, A, B)
MSG
SENSOR STATUS (Display sensor status.)
INTERNAL GPS (Displays data about internal GPS receiver.)
CPA (0.0 - 6.00,
6.0
(nm))
TCPA (0 - 60,
60
(min))
ALARM MODE (
ON
, OFF)
ALARM BUZZER (
ON
, OFF)
KEY BEEP (
ON
, OFF)
ALARM BUZZER (
ON
, OFF)
DISP RCVD MSG (
ALL
, ABM, OFF)
RCVD MSG BUZZ (
ON
, OFF)
LR MODE (
AUTO
, MANUAL)
AUTO SORT (
ON
,OFF)
CPA/TCPA ALARM
(Continued on
next page)
USER SETTINGS
INITIAL
SETTINGS
SET INT ANT POS.
A (
0
-511 (m))
B (
0
-511 (m))
C (
0
-63 (m))
D (
0
-63 (m))
SET MMSI (MMSI, IMO NO., NAME, C. SIGN)
SET EXT ANT POS.
SET SHIP TYPE (Type no.)
A (
0
-511 (m))
B (
0
-511 (m))
C (
0
-63 (m))
D (
0
-63 (m))
Note: The INITIAL SETTINGS sub menu
shown here is the one accessed with a
password, which permits changing of
settings. If accessed without a password,
in which case "SET" in a menu title is
replaced with "VIEW" and settings cannot
be changed.
SET I/O SET
COM
PORT
SET PC
PORT
SET LAN
PORT*
SET
PRIORITY
COM4 (
1
, 2, 3)
COM5 (1,
2
, 3)
COM6 (1, 2,
3
)
MODE (
STANDARD
, MONITOR, SERVICE, BEACON, DISABLE)
SPEED (4800BPS, 9600BPS, 19.2KBPS,
38.4KBPS
, 57.6KBPS)
SET COM1 MODE (
LONG RANGE
, EXT DISPLAY, DISABLE)
SPEED (IEC61162-1,
EC61162-2
)
SET COM2 MODE (
EXT DISPLAY
, MONITOR, HI LEVEL IF, DISABLE)
SPEED (
I
IEC61162-1,
EC61162-2
)
SET COM3 (Same as SET COM2.)
SET COM4 MODE (
SENSOR
, EXT DISPLAY, DISABLE)
SPEED (
IEC61162-1
, IEC61162-2)
SET COM5 MODE (SENSOR(Fixed)
SPEED (
IEC61162-1
, IEC61162-2)
SET COM6 MODE (SENSOR(Fixed)
SPEED (I
IEC61162-1
, IEC61162-2, AD-10)
* Shown when
optional LAN kit
is installed.
COM4 (1,
2
, 3)
COM5 (1, 2,
3
)
COM6 (
1
, 2, 3)
PORT