Filter
Top Products
PROGRAMMING INSTRUCTIONS
11. Instant Personal Panic
Press and release transmitter button #4 to sound the instant panic siren. The lights and siren will
activate for 30 seconds and then shut off. To stop the siren before the 30 seconds, press any of the
4 transmitter buttons.
12. Valet Mode
The valet mode prevents the system from arming. To activate valet mode, first disarm the system. Hold
down button #4 for 10 seconds. The system will chirp 1 time. Press button #4 again within 2 seconds.
The system will chirp once. The LED will remain solid red win in valet mode. To deactivate the valet,
repeat the above, however, the system chirps twice when you press button #4 the second time. The LED
turns off. This feature is useful when having your vehicle valet parked, washed or serviced. While in
valet mode keyless entry and instant panic will still work, however the alarm will not arm. Valet mode
may also be programmed while the engine is running.
13. LED Status Indicator
The LED (red light) provides valuable information about the system and is also a theft deterrent.
LED Status LED Display
Armed......................................Flashing Slow
Disarmed.............................................Off
Passive Arming.........Flashing Fast (arming count down)
Valet ......................................Constantly On
Violated Zone Triggered Device # of Flashes
Zone 2.............................On Board Shock Sensor 2 Flashes
Zone 3..................................External Sensors 3 Flashes
Zone 4 ....................................Voltage Sensor 4 Flashes
Zone 5 ....................................Door Switches 5 Flashes
14. Plug In Override Switch
In the event your remote control is lost, damaged or malfunctions; this switch allows you to disarm
your system. You must first open the door to the vehicle, turn ignition to the "ON" position, then
press the override switch. The siren will silence and you will now be able to start the engine. NOTE:
A door must remain open during this procedure.
15. Anti-Carjacking Protection • Not available on 6002/5002
We strongly recommend you use this feature only in unsafe neighborhoods. To activate the anti-carjacking
system, flip the toggle switch forward to the "ON" position. To turn the anti-carjacking system off,
switch the toggle backward to the "OFF" position. If any door is opened and then shut when the anti-
carjacking switch is in the "ON" position and the engine is running, the siren will sound and the lights
will begin to flash in one minute. If the engine is shut off it will not restart. If activated, to
turn off the anti-carjacking you must turn the ignition off, flip the toggle backward to the "OFF"
position and then press button #1 on the transmitter. We recommend turning the anti-carjacking off
when in safe areas. The 1 minute time delay allows you to leave the area of danger and later makes
the car undriveable for the carjacker. Unlike a normal violation, the alarm will not reset after 30
seconds. The siren will continue to sound and the lights will continue to flash until the proper
deactivation steps have been performed. To deactivate the anti-carjacking protection, turn the ignition
switch off, flip the toggle backwards or to the "OFF" position, then press transmitter button #1. The
siren will chirp twice, confirming that the anti-carjacking protection is disengaged. You may now start
the engine. NOTE: If you accidentally activate the anti-carjacking protection, you may deactivate it
before or after the siren sounds. (IT MUST BE DONE WITHIN 1 MINUTE OR THE SIREN WILL SOUND.)
CAUTION: DO NOT TURN ON THE DOME LIGHT WHILE THE ANTI-CARJACKING PROTECTION IS ENGAGED. THIS WILL ALSO
ACTIVATE THIS PROTECTION FEATURE.
1. Activating Current Sensing Factory setting is off
To activate current sensing, disarm the system, and hold button #4 for 10 seconds. The system will chirp once
again. To deactivate current sensing; repeat the above except you will hear 2 chirps after pressing button #3.
2. Activating the Shock Sensor Factory setting is on
To deactivate the shock sensor, disarm the system, then press and hold button #4 for 10 seconds. The system will
chirp once, Press button #2 within 2 seconds. The system will chirp twice. To activate the shock sensor; repeat
the above except you will hear 1 chirp after pressing button #2.
12