Filter
Top Products
SYSTEM PROGRAMMING - Menu 1
PAGE 21
80 SERIES
INSTALL MANUAL
PROGRAM MODE
SYSTEM PROGRAMMING - Menu 1
PAGE 20
80 SERIES
INSTALL MANUAL
PROGRAM MODE
CON'T FROM PREVIOUS PAGE
CHANGE SETTING 4 -
GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 4- SIREN OPTIONS
THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED
4 CHIRP
PRESS
1 TIME
4X
1 CHIRP
2 CHIRP
3 CHIRP
CHANGE SETTING 5 -
GOTO SETTING 6 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 5- RESERVATION MODE
THE SIREN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED
5 CHIRP
PRESS
1 TIME
5X
1 CHIRP
2 CHIRP
SETS OPTION 1 – PRESS # - Press and release the # button while the park brake is
applied and the vehicle is running.
SETS OPTION 2 – BRAKE ACTIVATION- Press and release the brake 2 times
while the park brake is applied and the vehicle is running. (DEFAULT)
SETS OPTION 1 - 30 SECOND DURATION- The siren will activate for 30 seconds
when the alarm is activated.
SETS OPTION 2 – PULSED OUTPUT- The siren output will pulse when activated.
(+) horn activation)
SETS OPTION 3 – 60 SECOND DURATION- The siren will activate for 30 seconds
when the alarm is activated. (DEFAULT)
1 CHIRP
CHANGE SETTING 1 -
GOTO SETTING 2 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 1- SELECTABLE OUTPUT
THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED
1 CHIRP
PRESS
1 TIME
2 CHIRP
3 CHIRP
1 CHIRP
1X
CHANGE SETTING 2 -
GOTO SETTING 3 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 2-SPECIAL DOOR LOCK OPTIONS
THE SIREN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED
2 CHIRP
PRESS
1 TIME
2X
SETTING 3-GAS/ DIESEL MODE
THE SIREN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED
3 CHIRP
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
2 CHIRP
3 CHIRP
CON'T ON NEXT PAGE
1 CHIRP
2 CHIRP
3 CHIRP
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 2 –SECOND ACCESSORY- The white wire on the 6-pin connector
acts as a Second Accessory output.
SETS OPTION 3 –SECOND IGNITION- The white wire on the 6-pin connector
acts as a Second Ignition output. (DEFAULT)
SETS OPTION 1 –TYPE 2 - The doors will unlock before remote start, lock when
remote starter starts and again when the remote start shuts down.
SETS OPTION 2 – RE-LOCK- The doors will automatically lock when the remote
starter shuts down.
SETS OPTION 3 – NORMAL OPERATION- No additional door lock or door
unlock pulses. (DEFAULT)
SETS OPTION 1 – SECOND STARTER- The white wire on the 6-pin connector acts
as a Second Starter output.
SETS OPTION 1 – NEGATIVE- The system will wait for the negative wait to start input
to turn off. (Starter will activate after 30seconds)
SETS OPTION 2 – 15 SECOND DELAY- The system will wait for 15 seconds before
activating the starter motor.
SETS OPTION 3 – GAS/POSITVE- If 12 volts present on the wait to start input
the system will wait for up to 30 seconds then start. (DEFAULT)
*ALARM MODELS ONLY
*MANUAL TRANSMISSION MODELS ONLY
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
SIREN CHIRP
ENTERING PROGRAM MODE 3
Press START
Button to
Select Menu 3
REMOTE BUTTON