Filter
Top Products
SYSTEM PROGRAMMING - Menu 1
SYSTEM PROGRAMMING - Menu 1
PAGE 2
PAGE 3
80 SERIES
80 SERIES
INSTALL MANUAL
INSTALL MANUAL
TABLE OF CONTENTS
QUICK VIEW WIRE DIAGRAM
1
5
3
2
4
6
1
2
3
4
5
6
7
8
9
10
11
12
13
1
3
2
4
OUTPUT TO ACTIVATE IGNITION CIRCUITTHE VEHICLES
SELECTABLE OUTPUT* (DEFAULT 2ND IGN)
12VOLT/ 30 AMP MAIN POWER INPUT
OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT
12VOLT/ 30 AMP MAIN POWER INPUT
OUTPUT TO ACTIVATE ACCESSORY CIRCUITTHE VEHICLES
SYSTEM GROUND INPUT
SELECTABLE PARK LIGHT OUTPUT (DEFAULT POSITIVE)
(+) SIREN OUTPUT / (-) HORN OUTPUT
AUXILIARY 1 OUTPUT/ PROGRAMMABLE OUTPUT.
(-) 2ND ACCESSORY/ PROGRAMMABLE AUXILIARY 2 OUTPUT
AUXILIARY OUTPUT TO ACTIVATE TRUNK RELEASE
REARM OUTPUT (PULSE WITH LOCK & AFTER START)
NEGATIVE SECOND START OUTPUT
DISARM OUTPUT (PULSE WITH UNLOCK & BEFORE START)
POSITIVE DOOR INPUT (+ WHEN DOOR OPENED)
DIESEL WAIT TO START (+ OR - INPUT) PROGRAMMABLE
TACH DETECTION INPUT (CONNECT TO COIL, INJECTOR...)
BRAKE SWITCH INPUT (12VOLT WHEN BRAKE IS PRESSED)
HOOD PIN SWITCH (GROUND WHEN HOOD IS OPENED)
PARK BRAKE INPUT (-) (”M” SERIES ONLY)
NEGATIVE DOOR INPUT (- WHEN DOOR OPENED)
Status Led’s
Program Button
QUICK VIEW WIRING DIAGRAM..........................................................3-4
Connector Pin Configuration
Antenna Connector
Park Light Jumper
MANUAL TRANSMISSIONS.....................................................................5
Park Brake Input
Door Pin Connections
Clutch Bypass
QUICK VIEW PROGRAMMING..............................................................6-9
Enter Program Mode
System Reset
Transmitter Programming
Menu 1,2,3 & 4 Quick View
Auto Tach Learning
Manual Tach Learn (Vehicles without start wire)
SYSTEM WIRING DETAILS................................................................10-14
Connector Views
Wiring Description
PROGRAM MENUS............................................................................15-23
Program Menu 1 Detailed
Program Menu 2 Detailed
Program Menu 3 Detailed
Program Menu 4 Detailed
DOOR LOCK DIAGRAMS..................................................................24-25
Relay Diagrams
SHOCK SENSOR (ALARM MODELS)....................................................26
Entering Adjustment Mode
Shock Sensor Adjustment
QUICK VIEW OPERATIONS CHART.......................................................27
Basic Operations
Service Mode/ Emergency Override
TRANSMITTER PROGRAMMING...........................................................28
Adding/ Reprogramming Transmitter
Second Car Operation & PAD LOCK
RESERVATION MODE (MANUAL TRANSMISSION)..............................29
How to Set Reservation Mode
DIAGNOSTICS..........................................................................................30
Diagnostic Chart
Diagnostic Memory
NOTES......................................................................................................31
CONTACT INFORMATION.......................................................................32
* The selectable output can be changed in the program mode to output as a 2nd Accessory or 2nd Start output.
Default output is second ignition. **This output does not change back to 2nd Ignition upon reset**
**Siren output on alarm models and horn honk output on starter models.
***A “M” series remote starter must be used when installing on a manual transmission vehicle. NEVER
INSTALL AN AUTOMATIC REMOTE START IN A MANUAL VEHICLE!!
**** The door pin connections are used on Manual Transmission and Alarm Models Only.
THE DOOR DIN CONNECTION MUST BE CONNECTED FOR PASSIVE ARMING ON THE 1280 and 3285.
BLACK
WHITE
ORANGE
BROWN**
BLUE
WHITE*
RED
YELLOW
RED
GREEN
WHT/VIOLET
ORANGE/WHT
RED/WHITE
YELLOW
GRAY
BROWN
PURPLE****
BLUE
BLUE/WHITE
GRN/WHITE
GREEN****
PINK
BLK/WHT***
(-) STARTER KILL/ ANTI-GRIND OUTPUT