Filter
Top Products
70
There are no traffic announcements.
•Activate TA (page 21).
• The station does not broadcast any traffic
announcements despite being TP.
tTune in another station.
PTY displays “None.”
• The current station is not an RDS station.
• RDS data has not been received.
• The station does not specify the program type.
The program service name flashes.
There is no alternative frequency for the current
station.
tTouch ./> while the program service name
is flashing. “PI Seek” appears and the unit starts
searching for another frequency with the same PI
(Program Identification) data.
Picture
There is no picture/picture noise occurs.
• A connection has not been made correctly.
• Check the connection to the connected equipment,
and set the input selector of the equipment to the
source corresponding to this unit.
• The disc is defective or dirty.
• Installation is not correct.
tInstall the unit at an angle of less than 45° in a
sturdy part of the car.
• The parking cord (light green) is not connected to the
parking brake switch cord, or the parking brake is not
applied.
The picture does not fit in the screen.
The aspect ratio is fixed on the DVD.
There is no picture/picture noise occurs in the
rear monitor.
•A source/mode which is not connected is selected. If
there is no input, no picture appears in the rear
monitor.
• The color system setting is incorrect.
tSet the color system to “PAL” or “NTSC”
according to the connected monitor (page54).
• The picture of the rear view camera is displayed on
this unit.
tNo picture appears in the rear monitor if the
picture of the rear view camera is displayed on
this unit.
Sound
There is no sound/sound skips/sound cracks.
• A connection has not been made correctly.
•Check the connection to the connected equipment,
and set the input selector of the equipment to the
source corresponding to this unit.
•The disc is defective or dirty.
•Installation is not correct.
tInstall the unit at an angle of less than 45° in a
sturdy part of the car.
•The MP3 file sampling rate is not 32, 44.1, or
48 kHz.
•The WMA file sampling rate is not 32, 44.1, or
48 kHz.
•The AAC file sampling rate is not 44.1 or 48 kHz.
•The MP3 file bit rate is not 48 to 192 kbps.
•The WMA file bit rate is not 64 to 192 kbps.
•The AAC file bit rate is not 40 to 320 kbps.
•The unit is in pause/reverse/fast-forward mode.
•The settings for the outputs are not made correctly.
• The DVD output level is too low (page 26).
•The volume is too low.
• The ATT function is activated, or the Telephone ATT
function (when the interface cable of a car telephone
is connected to the ATT lead) is activated.
• The position of the fader control “Fader” is not set for
a 2-speaker system.
•The format is not supported (such as DTS).
tCheck if the format is supported by this unit
(page 11).
Sound is noisy.
Keep cords and cables away from each other.
Disc operation
The disc cannot be loaded.
•Another disc is already loaded.
• The disc has been forcibly inserted upside down or in
the wrong way.
The disc does not play.
•The disc is defective or dirty.
•The disc is not playable.
•The DVD is not playable due to the region code.
•The disc is not finalized (page 64).
•The disc format and file version are incompatible
with this unit (page 11, 64).
•Press Z to remove the disc.
MP3/WMA/AAC/JPEG/Xvid/MPEG-4 files do not
play.
•Recording was not performed according to the ISO
9660 level 1 or level 2 format or the Joliet or Romeo
expansion format (DATA CD), or the UDF Bridge
format (DATA DVD) (page 64).
• The file extension is incorrect (page 65).
•Files are not stored in MP3/WMA/AAC/JPEG/Xvid/
MPEG-4 format.
• If the disc contains multiple file types, only the
selected file type (audio/video/image) can be played.
tSelect the appropriate file type using the list
(page 36).