Auto Page RS-1000 Automobile Alarm User Manual


 
RS1000 OP 1/07
19
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but
would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button on the transmitter. Twice if safety start has been
programmed. The LED indicator will flash 3 times to confirm.
2.Turn the ignition key to OFF position. (The engine will stay running.)
3.The engine will run until the pre-programmed time elapsed or a shutdown input is received.
D. TURBO TIMER MODE:
Turbo timer mode keeps the engine running after arriving at your destination for a
programmable period of 1, 3 or 5 minutes. This allows the system time to
conveniently cool down the turbo after you have left the vehicle. To activate the turbo
timer:
1. While engine is running, place the transmission gear in the park position and pull
up the hand brake.
2. Before turning off the engine, Spin up the
switch to the page 5 and then press
the “Turbo Start” button or press and release
and buttons at the same time.
-- The parking light will activate to indicate the remote start has entered turbo timer mode. --
3. Pull out the “Ignition Key” from the key cylinder.
-- The engine will continue to run. --
4. Exit and secure the vehicle.
-- Engine continues running until the pre-programmed time has elapsed. --
If you do not want the vehicle to continue running, simply step on the vehicle's brake, or activate the
button in succession. Any of these will cause the engine to turn off.
E. TIMER START:
Your system has the ability to automatically start the vehicle every 1,2 or 3 hours and run for the
pre-programmed time (5, 10, 20 or 30 minutes), and then shut off. This will continue for 6 cycles. This
feature is especially useful in cold climates where the only means to keep the engine and engine fluids
warm is to periodically start the engine.
If the system is set up to start in temperature mode, the system can be programmed to automatically start
the vehicle’s engine whenever the temperature inside the vehicle reaches or drops below the
preprogrammed temperature level. The system will monitor the air temperature every 3 hours and will only
start the engine during extreme cold temperatures.
WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle-starting
device. A running engine produces dangerous carbon monoxide fumes, which can be harmful or
fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.
Timer Start Operation:
1. Turn the ignition key on then off. Within 15 seconds …..
2-a. For 2-Way Transceiver: Spin up the
switch to the page 5
and then press the “Timer Start” button. or
2-b. For Regular one-way Transmitter: Press the
button first,
with 3 seconds press the
button.
3. The parking lights will flash and the siren will chirp 3 times indicating the timed start mode has been
activated.
Daily Timer Start Operation: The feature is very useful for a driver who wants to run the vehicle
at the same time the next day. NOTE:
Before setting-up of the “Daily Timer Start”, you should set your
time
Engine start time (See the “Daily Start Timer” Setting on page 10)
1. Turn the ignition key ON then OFF. Within 15 seconds …..
2. Spin up the
switch to the page 5 and then press the “Daily start” button.
3. The parking lights will flash and the siren will chirp 6 times indicating the daily
timed start mode is activated.
Cancel the timer start: To cancel the timer start do one of the following:
1. Start the vehicle manually with the use of the ignition key.
2. Remote start the vehicle using your keychain RF transmitter.