Filter
Top Products
Installation Guide
Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and siren chirps..
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 7- Sensor Disconnect
10
1 Positive Input To Start 1 Flash Positive pulse will activate remote starter.
2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
PROGRAM MODE - STARTER SETTINGS
Enter Starter Program Mode - See Page 7 for details on entering program mode
1 Chrysler / VW Re-Arm 1 Flash Unlock pulse before start and a lock pulse after start
2 GM Auto Re-Lock 2 Flashes Lock pulse after remote starter shuts off
3* Normal Operation 3 Flashes No additional re-lock pulses
1 Diesel Glow Plug 1 Flash W
2 Timed Delay 2 Flashes Ignition ON for 10 seconds before engaging remote starter
3* Gas Mode operation 3 Flashes Waits 2 seconds before engaging starter output
aits a Maximum of 3:20 second before starting.
1 Type 1 1 Flash Pulse after start and with lock
2 Type 2 2 Flashes Pulse after start only
3* Factory Re-arm 3 Flashes 0.75 second pulse with lock and after shutdown
Setting 1- Special Door Lock/ Unlock Operations
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated
2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated
3* 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated
1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged
2 3 Seconds 2 Flashes 3 sec Max time that starter will stay engaged
3* 5 seconds 3 Flashes 5 sec Max time that starter will stay engaged
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Sensor Disconnect
1 Positive Input To Start 1 Flash Positive pulse will activate remote starter.
2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.(Same as below)
3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.
Continued on next page...
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
Release the Program Button. Press momentarily to move to next program step or repeat to change selection.