A SERVICE OF

logo

xStack
®
DGS-3600 Series Layer 3 Managed Gigabit Ethernet Switch
SNMP Status Use this pull-down menu to enable or disable Simple Network Management Protocol (SNMP)
on the Switch.
RMON Status
Remote monitoring (RMON) of the Switch is Enabled or Disabled here.
Link Aggregation
Algorithm
The algorithm that the Switch uses to balance the load across the ports that make up the port
trunk group is defined by this definition. Choose MAC Source, MAC Destination, MAC Src &
Dest, IP Source, IP Destination or IP Src & Dest (See the Link Aggregation section of this
manual).
Switch 802.1X MAC Address may enable by port or the Switch’s 802.1X function; the default is Disabled.
This field must be enabled to view and configure certain windows for 802.1X.
Port-Based 802.1X specifies that ports configured for 802.1X are initialized based on the port
number only and are subject to any authorization parameters configured.
MAC-based Authorization specifies that ports configured for 802.1X are initialized based on
the port number and the MAC address of the computer being authorized and are then subject
to any authorization parameters configured.
Auth Protocol The 802.1X authentication protocol on the Switch is set to RADIUS EAP and can be
configured to Local.
802.1X Authen
Network RADIUS
Enables or disables 802.1X Authentication Network RADIUS. The default is Enabled.
Forward EAPOL
PDU
Enables or disables Forward EAPOL PDU. The default is Disabled.
HOL Prevention
If this option is enabled it prevents the forwarding of data to a port that is blocked. Traffic that
would normally be sent to the buffer memory of the Switch’s TX queue is dropped so that
memory usage is conserved and performance across all ports remains high.
Jumbo Frame
This field will enable or disable the Jumbo Frame function on the Switch. The default is
Disabled. When enabled, jumbo frames (frames larger than the Ethernet frame size of 1536
bytes) of up to 9216 bytes (tagged) can be transmitted by the Switch.
Syslog State
Enables or disables Syslog State. The default is Disabled.
Broadcast Ping
Reply State
Enables or disables the Broadcast Ping Reply State. The default is Enabled.
ARP Aging Time (0-
65535)
The user may globally set the maximum amount of time, in minutes, that an Address
Resolution Protocol (ARP) entry can remain in the Switch’s ARP table, without being
accessed, before it is dropped from the table. The value may be set in the range of 0 to 65535
minutes with a default setting of 20 minutes.
DVMRP State The user may globally enable or disable the Distance Vector Multicast Routing Protocol
(DVMRP) function by using the DVMRP Global Settings window (L3 Features > IP
Multicast Routing Protocol > DVMRP Global Settings or click Detail Settings)
.
PIM State The user may globally enable or disable the Protocol Independent Multicast - Dense Mode
(PIM-DM) function by using the PIM Global Settings window (L3 Features > IP Multicast
Routing Protocol > PIM > PIM Global Settings or click Detail Settings)
.
BGP State The user may configure Border Gateway Protocol (BGP) by using the BGP State Settings
window (L3 Features > BGP > BGP Global Settings or click Detail Settings)
.
OSPF State The user may globally enable or disable the Open Shortest Path First (OSPF) function by
using the OSPF Global Settings window (L3 Features > OSPF > OSPF Global Settings or
click Detail Settings)
.
OSPFv3 State The user may globally enable or disable the Open Shortest Path First (OSPF) version 3
function by using the OSPFv3 Global Settings window (L3 Features > OSPF > OSPFv3 >
OSPFv3 Global Settings or click Detail Settings)
.
DNS Resolver State The user may globally enable or disable the Domain Name Server Resolver function by using
the DNS Resolver Global Settings window (L3 Features > DNS Resolver > DNS Resolver
Global Settings or click Detail Settings)
.
7