Filter
Top Products
The following abbreviations are used to represent values for Control Module Pin-Out data
I Input PG Power Ground C CAN Network D Serial and Encoded Data
O Output SS Sensor / Signal Supply V S SCP Network V Voltage (DC)
B+ Battery Voltage SG Sensor / Signal Ground D2 D2B Network PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds, control
modules and control module pins.
DATE OF ISSUE: June 2002
Fig. 10.3
COMPONENTS
Component Connector(s) Connector Description Location
DOOR MIRROR – DRIVER DT6 22-WAY / BLACK DRIVER DOOR
DOOR MIRROR – PASSENGER CA19 22-WAY / BLACK PASSENGER DOOR
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
DRIVER DOOR CONTROL MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
ELECTROCHROMIC REAR VIEW MIRROR AND COMPASS RF5 6-WAY / BLACK WINDSHIELD, CENTER
REAR ELECTRONIC CONTROL MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
HARNESS IN-LINE CONNECTORS
Connector Connector Description / Location Location
DD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
DT10 10-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
RF34 16-WAY / GREEN / CABIN HARNESS TO DOOR HARNESS ‘D’ POST, UNDER PARCEL SHELF
GROUNDS
Ground Location
CA30 LH LOWER ‘A’ POST, ADJACENT TO THE GENERAL ELECTRONIC CONTROL MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA116 BEHIND REAR SEAT BACK, RH SIDE
CA156 LUGGAGE COMPARTMENT, RH SIDE
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT.
CONTROL MODULE PIN-OUT INFORMATION
Driver Door Control Module
Pin Description and Characteristic
O CA85-5 MIRROR FOLD FLAT DRIVE: TO ACTIVATE, DDCM SWITCHES CIRCUIT TO B+
O CA85-6 MIRROR FOLD FLAT DRIVE: TO ACTIVATE, DDCM SWITCHES CIRCUIT TO B+
PG CA85-7 POWER GROUND: GROUND
PG CA85-8 POWER GROUND: GROUND
B+ CA85-11 BATTERY POWER SUPPLY: B+
B+ CA85-12 SWITCHED SYSTEM POWER SUPPLY: B+
I DD4-20 MIRROR FOLD FLAT (MIRROR SELECT IN NEUTRAL POSITION): GROUND WHEN ACTIVATED
I DD4-23 LH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTED
I DD4-24 RH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTED
Rear Electronic Control Module
Pin Description and Characteristic
B+ CA101-3 BATTERY POWER SUPPLY: B+
SCA102-1 SCP +
SCA102-2 SCP -
OCA102-7 HEATED REAR WINDOW ACTIVATE: TO ACTIVATE, RECM SWITCHES CIRCUIT TO GROUND
PG CA102-12 POWER GROUND: GROUND
B+ CA103-13 SWITCHED SYSTEM POWER SUPPLY: B+
NOTE: Refer to the Appendix at the rear of this book for Network Messages.