Filter
Top Products
7
128-5560A
7 of 8
to produce 2 Chirps. This signifies that you have changed the programming to Chirps OFF. Please follow the
programming procedure carefully, and refer to the list of the Programmable Features above when programming the
APS-20LAD.
COMPLETING THE INSTALLATION:
After you have confirmed the operation of the APS-20LAD, and tested any and all optional features of the system:
1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain
that the chosen mounting location will not inhibit any of the controls of the vehicle.
2. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact
with under the dash board or in the engine compartment areas.
CAUTION: Particularly avoid the area around the steering shaft and column, as wires can wrap around these
mechanisms and impair the safe operation of the vehicle.
3. Shock Sensor Sensitivity Adjusting:
Note: The shock sensor's LED's will not operate unless the alarm system is armed.
The sensitivity of the pre-detect stage, (Indicated by the Green LED), and full trigger stage, (Indicated by the Red
LED) are set with one setting. The pre-detect stage will operate at a 30% force of the full trigger stage.
a. Arm your alarm system than firmly strike the windshield pillar with the open palm of the hand considering the
force required to break the vehicle glass. If the alarm system triggers easily, disarm your alarm, turn the adjustment
screw located on the sensor counterclockwise to decrease the units sensitivity, and repeat the above test. If the
siren emitted a few short bursts (pre-detect) no further adjustment is necessary.
b. If the unit failed to pre-detect, increase the sensitivity setting by turning the adjustment potentiometer clockwise.
Note: Proper sensitivity level is dependent mostly upon technician preference, mounting location, and vehicle size.
Always consider the effect of setting the sensitivity level too high. This will cause false triggers due to environment
noise and passing vehicle vibrations. Keeping your settings at a minimum will prevent these problems.
4. Check the vehicle's wipers, lights, horn, etc... to insure proper operation.
5. Replace all panels that were removed during installation, and retest the system.
6. Explain the operation of the system and its various features to the end user if available, and place the Owner's
Manual on the dashboard for them to find and review.
FEATURE ACTION TO PERFORM RESPONSE FROM SYSTEM LED FLASH PATTERN
To Turn the Ignition Switch ON LED Turns OFF
Enter Toggle the Valet/Program/Manual Override Switch
The ON then OFF 3 Times 1 Siren/Horn Chirp & 1 LED Flash
Programming Within 3 seconds
,
Mode turn the Ignition Switch OFF, then ON 1 Short Chirp, and 1 Long Chirp
First Press Arm/Disarm Button to Adjust Feature 1 Chirp = Passive Arming ON 1 Flash, Pause, Repeat
2 Chirps = Active Arming ON
Second Press Arm/Disarm Button to Adjust Feature 1 Chirp = Ign Locking ON 2 Flashes, Pause, Repeat
2 Chirps = Ign Locking OFF
Third Press Arm/Disarm Button to Adjust Feature 1 Chirp = Ign Unlocking ON 3 Flashes, Pause, Repeat
2 Chirps = Ign Unlocking OFF
Fourth Press Arm/Disarm Button to Adjust Feature 1 Chirp = Passive Doorlock ON 4 Flashes, Pause, Repeat
2 Chirps = Passive Doorlock OFF
Fifth Press Transmitter Button 1 to Adjust Feature 1 Chirp = Chirps ON 5 Flashes, Pause, Repeat
2 Chirps = Chirps OFF
You have now engaged the Programming Mode, and are set to adjust the First feature
This mode will time out automatically in 15 seconds, or can be cancelled by turning the Ignition Switch OFF
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Turn the Ignition Switch OFF to exit the Programming Mode
NOTE:
If you accidentally toggled past the feature you intended to adjust, you must exit and re-enter the mode.
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature