Filter
Top Products
6
128-5560A
6 of 8
connector, it will only plug in one way. Note: Please refer to the section; "Programming System Features" shown
later in this installation guide to learn the operation of the valet/program/manual override switch.
POWER DOOR LOCK HARNESS
2-PIN White Plug w/2 Wires; Red & Green
The connection of the power door lock/unlock wires has already been explained. Route the Red and Green wires
to the APS-20LAD unit and plug the white 2-PIN connector into the mating white two pin connector shell of the
APS-20LAD control module. Do not force the connector, it will only plug in one way.
TRANSMITTER PROGRAMMING:
The transmitters supplied with the APS-20LAD are pre-programmed at the factory to provide the following function:
Arm/Disarm, pressed and released quickly = Arm/Disarm (Lock & Unlock) w/Siren Chirps
Arm/Disarm, pressed for ~ 1 second = Arm/Disarm (Lock & Unlock) w/o Siren Chirps
Arm/Disarm, pressed for ~ 3 seconds = Engage/Disengage Panic Mode
Option, pressed for ~ 3 seconds = Channel 2 Output
If you desire to have the transmitters operate differently from this factory configuration, please refer to the separate
Transmitter Programming Guide that came with the APS-20LAD system.
PROGRAMMING FEATURES:
There are five (5) Programmable Features on the APS-20LAD system. Study the list below, keeping in mind the
features and their defaults, (how it comes programmed from the factory), and decide how best to program the
APS-20LAD for your particular installation.
Programmable Features:
Features 1 Chirp 2 Chirp Default
First Passive Arming Active Arming Passive Arming
Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF
Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF
Fourth Passive D/L Active D/L Active D/L
Fifth Chirps ON Chirps OFF Chirps ON
To Program These Features:
Entering the Programming Mode involves operating the Ignition Switch and the Valet/Program/Manual Override Switch
in a particular sequence. This sequence is very time dependent, in other words it must be performed
quickly in order
for you to enter the mode. This sequence is also only one step different from the Transmitter Programming Mode,
so make certain you perform the sequence properly.
Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Pro-
grammable Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing arm/
disarm of the transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED
once, with a pause in between each flash. The system will then report how the feature has been set by the number
of chirps heard after pressing the transmitter button. Toggling the Valet/Program/Manual Override Switch once
again will advance you to the Second Programmable Feature, confirmed by a repeating two LED flashes, with a
pause in between each flash, etc., etc.
It is important to note that when you first enter the Programming Mode, you are automatically positioned to adjust the
First Programmable Feature, and that the Valet/Program/Manual Override Switch allows you to toggle from there
through each of the four more programmable features. However, it will not allow you to return to any feature once
you have toggled past it. Should you accidentally toggle past the feature you wanted to program, you must exit and
re-enter the Programming Mode and then adjust the feature you missed.
It is also important to note that you may toggle past as many programmable features as you wish without having to
adjust them. Each time you toggle forward to a new feature, the siren will chirp the appropriate number of times (1
or 2 times) to indicate how that feature is currently set, and the LED will flash the appropriate number of times to
indicate the number of the feature (First through Fifth) that you are set to adjust. For example, you might enter the
mode and toggle the Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable
feature. The system would respond with 1 Chirp, and the LED would begin to flash 4 Flashes, pause, and repeat.
This has told you that the system is ready for you to adjust the Fourth programmable feature, and that it is currently
programmed for Chirps ON. A single press of the arm/disarm button of the transmitter will cause the system