Ultra Start 4500 Automobile Alarm User Manual

Open as PDF

of 16

Installation Guide

PROGRAMMING

Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)

Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.

Release the Program Button. Press momentarily to move to next program step or repeat to change selection.

Setting 1 - Service Mode (Valet Mode)

Setting 2 - Parking Light Output

Setting 3 - Horn Honk Timing - Pink wire on 3-pin white

Setting 4 - 4th Channel Settings- White/Green wire on 4-pin square

Setting 5 -Car Jack Mode

Setting 7 -Programmable Output - Green Wire on 3-pin white

Setting 6 - Horn / 5th Channel - Pink wire on 3-pin white

1 Pulsed 1 Flash Pulsed for 0.75 seconds upon 4th Channel Activation

2 Latched 2 Flashes Latched until repeated or ignition “ON”

*3 Active 3 Flashes Active for as long as buttons are held on Transmitter

1 Door & Button 1 Flash Car Jack is activated upon Button 4 or Door open while Ignition is “ON”

2 Door, Button 4 2 Flashes Car Jack is upon Button 4 or Door open or ignition “ON” and Ignition

*3 Car Jack OFF 3 Flashes No Car Jack Functions

1 LED Output 1 Flash The output will pulse (-) when armed for activation of an LED.

2 Low Crank 2 Flashes The output will come on (-) during crank duration.

*3 (-) Disarmed 3 Flashes Negative while disarmed.

1 5th Channel 1 Flash Pulsed output when activated by buttons #2 & #3 held for 2 seconds

2 Horn Honk 2 2 Flashes Horn Honk Output - Full Alarm ONLY

*3 Horn Honk 1 3 Flashes Horn Honk with Arm & Disarm Chirps

1 30 Second Park Lights 1 Flash Park Lights on for 30 seconds on disarm

2 Negative Park Lights 2 Flashes Switches the Park Light and the Trunk Release (3rd Channel) Outputs

3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm

1 5ms 1 Flash Short (Quiet) Pulses

2 20ms 2 Flashes Long (Loud) Pulses

*3 10ms 3 Flashes Normal (Medium) Pulses

1 Secure Valet Active 1 Flash Turn the ignition on and hold the Program Button for 15 seconds

2* Normal Valet Active 2 Flashes Turn the ignition on and hold the Program Button for 5 seconds

Note: To activate the 4th channel output, press and hold transmitter buttons #1 and #3 at the same time. The siren

will chirp once to confirm 4th channel activation.

Note: To operate the 5th channel, this setting must be programmed for setting #1. To activate the output press

buttons #2 and #3 together for two seconds..

1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse

2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock

*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock

1 Ignition Lock & Unlock Enabled 1 Flash Doors Lock / Unlock when the key is turned On/ Off

2 Ignition Lock Only 2 Flashes Doors Lock when ignition key is turned ON only

*3 Ignition Auto Lock Disabled 3 Flashes Doors do not Lock or Unlock with Ignition key

1 Lock & Unlock chirps Disabled 1 Flash Chirps for Panic and Car Finder Mode only.

2 Lock & Unlock chirps Enabled 2 Flashes Chirps for Lock, Unlock, Panic and Car Finder Mode Only.

*3 All chirps enabled 3 Flashes Chirps for Lock, Unlock, Start, Panic and Car Finder Mode.