Ultra Start 4500 Automobile Alarm User Manual

Open as PDF

of 16

Installation Guide

Enter Starter Program Mode - See Page 7 for details on entering program mode

PROGRAM MODE - TACH SETTINGS

Setting 1- Method 2- Low Idle Tach Learning

Setting 2- Adjust For Over-Crank

Setting 3- Adjust For Under-Crank

Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time.

Step 2 - Enter Program Menu 4 - Press Button #4 on the remote.

Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.

Step 4 - Press the Program Button - One time (LED- flashing in single cycles) then press and hold button for (5sec).

Step 5 - Release Program - Led should come on steady to indicate correct tach signal the park light will flash to confirm.

Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.

Step 2 - Enter Program Menu 4 - Press Button #4 on the remote.

Step 3 - Press the Program Button - 2 times (Led will start flashing 2 times).

Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is reduced).

Step 5 - Release Program - Exit Program Mode and remote start to test.

Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.

Step 2 - Enter Program Menu 4 - Press Button #4 on the remote..

Step 3 - Press the Program Button - 3 times (Led will start flashing 3 times).

Step 4 - Press and Hold Program - For 5 seconds until parking lights flash (each time lights flash tach is increased).

Step 5 - Release Program - Exit Program Mode then remote start to test.

This option is used for vehicles that maintain a HIGH or erratic idle after starting and need more that 10

seconds to establish a stable idle.

Setting 1 - Method 1- Auto Tach Learning. See page 7.

1 Type `1 1 Flash Unlock pulse before start, lock pulse after start and after shutdown

2 Type 2 2 Flashes Lock pulse after remote starter shuts off

3* Normal Operation 3 Flashes No additional re-lock pulses

1 Negative Glow Plug 1 Flash Waits a Maximum of 30 second before starting.

2 Timed Delay 2 Flashes Ignition ON for 10 seconds before engaging remote starter

3* Gas/ Glow Plug (+) 3 Flashes If no diesel input is detected the vehicle will start after two seconds.

1 Type 1 1 Flash Pulse after start and with lock

2 Type 2 2 Flashes Pulse after start only

3* Factory Re-arm 3 Flashes 0.75 second pulse with lock and after shutdown

Setting 1- Special Door Lock/ Unlock Operations

Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin

Setting 3- Rearm Output- Yellow Wire on 14-Pin

1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated

2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated

3* 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated

1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged

2 3 Seconds 2 Flashes 3 sec Max time that starter will stay engaged

3* 5 seconds 3 Flashes 5 sec Max time that starter will stay engaged

Setting 4- Run Time

Setting 5-Maximum Crank Time

Setting 6- Starter Kill / Aux. Horn - Orange wire on 14-Pin Con.

1 Horn Output 1 Flash Pulsed output to activate negative horn.

2* Starter Disable 2 Flashes Negative output while the system is armed

1 Safety ON 1 Flash Must press the start button twice to remote start vehicle

2* Safety OFF 2 Flashes Press the start button once to remote start vehicle.

Setting 8- Safety Start Mode

Setting 7- Sensor Disconnect - Blue wire on 3-Pin Con.

1 Positive Start Input 1 Flash Positive pulse will activate remote starter.

2 Positive Disconnect 2 Flashes Alarm will trigger if disconnected from 12 volts.

3* Positive Disconnect 3 Flashes Alarm will trigger if disconnected from 12 volts.

Continued on next page...

Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)