Filter
Top Products
Installation Guide
Installation Guide
QUICK START INSTALL
Yellow Starter Output Connect To The Vehicles Starter Wire.
Green Heater Output Connect To The Vehicles Accessory Wire.
Red 12 power Input Connect to Constant 12 Volt Power Source- High Current.
Red 12 power Input Connect to Constant 12 Volt Power Source- High Current.
Blue Ignition 1 Output Connect To the Vehicles Primary Ignition.
White Selectable Output Select Jumper Position (If Necessary). See Page 5.
6 Pin Power Connector
14 Pin Power Connector
Manual Transmissions Only
Step 2- Plug-In The Module
Step 3- Auto Tach Learn
Your Basic Install Is Complete!
Black/White Park Brake Connect Park Brake Switch. (-) When Brake is applied.
Manual transmission vehicles must have a “M” Series Remote Starter Installed. Manual Transmission Units Must
Be Placed Into Reservation Mode To Operate. See Page 12.
Your Basic Installation is Now Complete!!
1) Make all the required wire connections and plug-in the Unit.
**The park lights should flash twice upon power up.
2) Turn the Ignition Key ON. (Park Lights will turn on).
3) Start the vehicle, LED’s on the antenna will come on to confirm tach signal is detected**, then after two to 40
seconds the park lights will turn off then flash twice to confirm tach learning.
* The system will flash the park lights seven times if not tach learned and the start button is
pressed. The system must be tach learned before remote starting.
** If the LED’s do not come on during tach learn, a proper tach signal was not detected.
*** A system reset must be preformed before the tach can be re-learned. (Page. 7)
Note: If the park lights do not flash in auto tach learn mode it may be that the first ignition wire (Blue) is connected
to a wire that turns off during crank. If the ignition connection is good, it may be necessary to connect to a
different tach source. For best results connect the tach wire to the coil pack or to a fuel injector wire. If
necessary See Page 11. for Tach Adjustment.
NOTES:
1) If the unit does not start, check the starter is not in Tach Lock Out or in Program
Mode.
2) If the vehicle still does not start, check all connections and check for factory
security.
When all the connections are done, the control module can be plugged in. Before connecting the control module,
make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by any other
connectors that were used.
Program mode allows you to adjust the settings and options of your system.
Your system has been intelligently designed by installers with years of experience. The system’s default settings
do not require any program changes in most cases. However, this system does incorporate a highly advanced
programming system that includes 4 menus with numerous options and settings that can be easily adjusted for
custom installations and applications.
Menu 1 - User Settings - Page 8
This program menu contains settings that adjust the way the system operates for the user.
Menu 2 - Alarm Settings - Page 9
This program menu contains settings that adjust the way the system operates for the user.
Menu 3 - Starter Settings - Page 10
This menu controls features and settings associated with remote car starter applications.
Menu 4 - Tach Settings - Page 11
This menu allows the programming of the tach signal and the manual adjustment of that setting.
Programming Overview
Entering Program Mode
Changing the Programmable Settings
To Enter Program Mode
1) Make sure ignition is in the off position.
2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave in the “ON” position.
3) Press and release the Program Button on the antenna one time.
4) The park lights will come on and the siren will chirp to confirm entering Program Mode.
5) Select the Desired Program Menu:
Press Button #1 User Options See Page 8
Press Button #2 Alarm Option See Page 9
Press Button #3 Remote Start Options See Page 10
Press Button #4 Tach Adjustment Menu See Page 11
6) The selected mode will be confirmed by a siren chirp and one park light flash.
7) The Program Menu may be changed at any time by pressing the transmitter buttons as above, this allows
the installer to change a setting from one menu, then quickly jump to another menu and change another
setting without re-entering the Program Mode.
8) To exit Program Mode, Turn the ignition key “OFF” or wait 30 second and the system will exit automatically.
This will be confirmed by one long siren chirp and park light flash.
Note: If unit does not enter Program Mode, turn the ignition off then repeat steps 1-4.
** The first ignition(Blue wire) MUST be connected to the vehicle’s first ignition wire. If it is not connected it
will not be possible to enter the Program Modes.
To Select and Change A Program Setting:
1) Enter Program Mode.
2) Select the desired Program Menu. (See pages 8 - 11)
3) Press & release the Program Button the correct number of times to select the desired Program
Setting(as listed on pages 8 - 11). The park lights will flash and the siren will chirp to indicate the current
setting that is selected.
4) Press and hold the Program Button until the parking lights / siren confirm the selected setting. The park
lights will flash and the siren will chirp to indicate the option selected within the setting.
5) Turn the ignition key “Off” to exit Program Mode.
Note: This procedure is listed in detail below each program setting on pages 8 - 11.
PROGRAMMING
SYSTEM RESET
7
Black System Ground Connect To Chassis Ground.
Pink Brake Switch Connect To (+) When Brake is Applied.
White Park Lights Connect To (+) Park Light System.
Green/White Hood Pin Connect To Hood Pin Switch.
Blue/White Tach Connect To Tach Source.
White/Blue Siren Connect To (+) Siren (4-pin square harness)
Green or (-) Door Input Connect the Green wire to a (-) door pin system.
Purple (+) Door Input Connect the Purple wire to a (+) door pin system.
Activate Self Learning Impact Sensor
1) Press Button #1 on the remote 5 times, once every second. The siren will chirp 3 times and the park lights will
come and stay ON. (If this does not happen, wait five seconds and repeat step 1)
2) While the park lights are on, strike the vehicle three times at the desired level to trigger the alarm.
3) The siren will respond with one chirp each time a impact is detected by the Shock Sensor.
4) Press the button #1 to exit Shock Sensor learning.
STEP 1 - Within three seconds turn the key ON-OFF-ON-OFF-ON (Leaving Key ON).
STEP 2 - Press and release the Program Button.
STEP 3 -The park lights will turn ON.
STEP 4 - Press the Program Button a second time and hold for 8 seconds until the park lights flash and the
siren will chirps three times. The system is now re-set to factory defaults.
Note: Reset to defaults does not delete the transmitters from memory.
6