Filter
Top Products
Installation Guide
Installation Guide
OPERATIONS
OTHER FEATURES
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most
installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the
activation of the remote starter. Never disconnect or alter the switch to be always bypassed. Always use a “M”
Series Remote Starter on a manual transmission vehicle.
Never install a automatic Remote Starter model into a manual transmission vehicle. It is not recommended to
install a remote starter on a convertible type vehicle. If doing so It is highly recommended that a radar sensor is
installed to cover the proximity of the gear shift lever. If the radar sensor is tripped the remote starter will exit
Reservation Mode.
To enter Reservation Mode, the following steps must be followed.
Step 1 - While the vehicle is running, place the transmission in neutral and apply the parking brake.
Step 2 - Press and release the brake pedal. The park lights will activate.
Step 3 - Turn the ignition key off and the vehicle will stay running.
Step 4 - Exit the vehicle and close the door. The vehicle will then shut off*.
Step 5 - The vehicle can now be safely remote started.
* If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off. This is normally
no longer than 30 seconds. Reservation Mode will automatically be exited if the doors of the vehicle are opened.
The set-up mode will then have to be repeated . Reservation Mode Must be set-up each time the vehicle is
parked.
Note: If the vehicle is not in Reservation Mode and the Start button is pressed, the system will
flash the park lights four times slowly.
Reservation Mode - Manual Trans.
13
12
Emergency Service Mode - (Valet Mode)
This feature will disable the system except for locking and unlock functions.
This mode can also used if a remote is lost, damaged or if the system malfunctions.
ENTERING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button on the
antenna for 5 seconds or until the siren chirps 5 times.
EXITING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button for 5
seconds or until the siren chirps 2 times.
Note: Remote starter functions will be disabled and the LED will be “on” steady.
The door locks and the trunk release will still be operational.
Ignition
“On”
7 sec.
ATTENTION: THE SYSTEM MUST BE PLACED INTO SERVICE MODE BEFORE ANY UNDER HOOD
SERVICING IS DONE TO THE VEHICLE. IT IS THE RESPONSIBILITY OF THE VEHICLE’S OWNER TO
INSURE THAT THIS IS DONE. THE MANUFACTURER ACCEPTS NO RESPONSIBILITY FOR
ACCIDENTAL STARTING WHILE VEHICLE IS BEING SERVICED.
Battery Replacement
1
Lift
Slide
+
-
System Service Mode (Valet) - By Remote
This feature will disable the system from the remote transmitter. Use this feature must be
used when having the vehicle serviced. ( Oil change, Tune-up etc.)
ACTIVATE Service Mode (User Programmable Feature)
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button #3 and the ? symbol will come on solid.
4 - Press button #4 to exit User Program Mode.(System Is Now In Service Mode)
5 - The siren will chirp once and the LED’s on the antenna will come on solid.
DEACTIVATE Service Mode
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ? starts flashing on the LCD screen.
3 - Press button# 2 and the ? symbol will turn off.
4 - Press button# 4 to exit User Program Mode.(Serice Mode is Deactivated)
5 - The siren will chirp once and the LED’s on the antenna will turn off.
Note: Remote starter functions will be disabled and the LED will be “On” steady.
The door locks and the trunk release will still be operational.
Quick Timer (Selects Last Programmed Start Interval)
1. Enter Transmitter Program Mode.
2. The Telephone Icon will begin to flash on the LCD screen.
3. Press Button #3 and the Telephone Icon will come on solid and the key Icon will begin to flash.
4. Press Button #4 to exit Transmitter Program Mode.
5. The remote starter will now start in the last programmed start interval.
Note: Timer Mode will reset if the ignition key is turned to the “On” position. If this occurs the above
steps will have to be repeated.
When the Battery Icon on the remote indicates that the battery is low the battery should be changed
promptly. Replace with quality 1.5volt “AAA” battery.
Transmitter Operation
1
2
3
4
1
2
3
4
4 - 3
2 & 3
1 & 3
Press Once to Lock / Unlock Doors and arm/disarm the alarm.
Press 2nd Time (within 3 sec.) and Hold for Constant Lock Output.
Press and hold for 3 seconds to activate Panic Mode.
Press again to disable panic when activated.
While running with the key, press the button to activate Idle Mode.
Press and Hold for Trunk / Aux Output
*Note this will also unlock doors and disarm alarm
Press Once for Start - (2 Times if programmed for Safety Start).
Press and Hold for 3 seconds while running to turn off.
While running with the key, press the button to activate Idle Mode.
Press and Release for Status Check.
Hold for 3 seconds to enter User Programmable Features
While running with the key, press and release to activate Turbo Timer Mode.
Press and release button #4 then press and hold button #3 for three seconds to
activate/Deactivate the Timer Mode
Press both buttons for 3 seconds to activate Car Finder Mode or 5th channel (see
page 9, setting 6)
Press both buttons for 1-2 seconds to activate 4th Channel (see page 9, setting 4)