Filter
Top Products
OPTION PROGRAMMING
12. HORN OUTPUT / CARJACK WITH HANDS-FREE REMOTE (2 FEATURES)
This option controls whether the system’s Factory Horn output AND full-time Carjack operation. There are 3
selections: Button 1 (Lock) = Horn Output Pulses on trigger and Full-time Carjack are disabled. Button 2
(Unlock) = Horn Output is on Solid when triggered. Button 3 (Trunk) = Enable Carjack using Hands-Free
remote transmitter. (See Carjack on page 16 for more information)
NOTE: TO ENABLE CARJACK USING HANDS-FREE TRANSMITTER, A HANDS-FREE TRANSMITTER
MUST FIRST BE PROGRAMMED TO THE SYSTEM AT OPTION LEVEL #21 (BUTTON #3)
13. AUX #2 OR SECOND ARMED OUTPUT
This option controls the system’s Aux. #2 output. Button 1 (Lock) = Auxiliary Channel 2. Button 2 (Unlock) =
Auxiliary Channel 2 functions as a Armed output wire activating when the system is armed.
14. AUX #1 OUTPUT CONFIGURATION
This option allows you to configure how the system’s Aux. Channel #1 output operates. There are three
choices: Button 1 (Lock) = Pulsed. Button 2 (Unlock) = Timed. Button 3 (Trunk) = Latched
NOTE: Computer, Securlinc™ Software, and Datalinc cable are required for setting up the timed output.
15. AUX #2 OUTPUT CONFIGURATION
This option allows you to configure how the system’s Aux. Channel #2 output operates. There are three
choices: Button 1 (Lock) = Pulsed. Button 2 (Unlock) = Timed. Button 3 (Trunk) = Latched
NOTE: Computer, Securlinc™ Software, and Datalinc cable are required for setting up the timed output.
16. AUX #3 OUTPUT CONFIGURATION
This option allows you to configure how the system’s Aux. Channel #3 output operates. There are three
choices: Button 1 (Lock) = Pulsed. Button 2 (Unlock) = Timed. Button 3 (Trunk) = Latched
NOTE: Computer, Securlinc™ Software, and Datalinc cable are required for setting up the timed output.
17. DISARM WITH AUX. OUTPUT 1 (TRUNK POP)
Controls whether the system will or will not DISARM when the trunk pop or AUX. channel #1 is activated.
When the feature is turned on the unit will DISARM when opening trunk or using an auxiliary device controlled
by the Gray output wire.
OPTIONS #18 through 20 WITH SECURLINC™ REMOTE START EXPANSION MODULE ONLY
18. REMOTE START IN VALET
This option only applies when using the SecurLinc™ Remote Start Expansion module. Allows to user to
determine whether the system will allow a remote start when in valet mode.
19. LEARN TACH / GAS or DIESEL ENGINE
This option controls tach learning and setting the Remote Starter module for Gas or Diesel engine type. Button
1 (Lock) programs engine RPM (Tach input). Note: Engine must be running. Button 2 (Unlock) sets the
remote start module for Gas engines. Button 3 (Trunk) sets the remote start module for Diesel engines. The
system will monitor the Positive or Negative Glow plug circuit when in Diesel mode.
20. AUTOMATIC START: TEMPERATURE, or VOLTAGE THRESHOLD (PC Data Linc / Software req’d)
This option controls the remote start module’s Auto Start feature. Button 1 (Lock) disables auto start (off for
default value). Button 2 (Unlock) sets the remote start module for Auto Start at a specific temperature. NOTE:
Specific Temperature can only be set when using a computer, Securlinc Software, and Datalinc cable. Button
3 (Trunk) sets the remote start module for Auto Start at a specific Voltage drop. NOTE: Specific Voltage can
only be set when using a computer, Securlinc Software, and Datalinc cable. The Remote start expansion
module system will monitor the voltage or temperature and Automatically start when necessary. NOTE: When
using the Auto Start Feature, the vehicle should be outdoors or in a well ventilated open area.
21. ENABLE 2-WAY FM MODULE, PROGRAM 2-WAY PAGER REMOTE, LEARN HANDS-FREE REMOTE
This option allows the 2008 system to operate with a 2-way remote pager expansion module, Learn a Pager
Remote, or Learn a Hands-Free Transmitter. Button 1 (Lock) enables the 2008PC system to work with the
SecurLinc 2-Way paging expansion module. Button 2 (Unlock) learns a 2-Way pager remote. Button 3
(Trunk) learns a Hands-Free transmitter.