Filter
Top Products
Matrix of user-selectable features
Feature Select
Column 1
1st latched
Column 2
2nd latched
Column 3
3rd latched
Column 4
4th latched
Column 5
5th latched
Row 1
1st momentary
Sound 1: on/off
info on page 18
Add new remote to channel 1
info on page 8–9 NOTE 1
Test/adjust primary (normal) zone
of the Proximity Sensor
info on page 14 NOTE 7
QuietChirps: on/off
info on page 18
Headlight Reminder: on/off
info on page 17
Row 2
2nd momentary
Sound 2: on/off
info on page 18
Add new remote to channel 2
info on page 8–9 NOTE 2
Test/adjust secondary (high) zone
of the Proximity Sensor
info on page 14 NOTE 8
Long-term
chirp silencing: on/off
info on page 18
Channel 2 headlight timer:
1sec–2.5min (30sec)
info on page 10 NOTE 10
Row 3
3rd momentary
Sound 3: on/off
info on page 18
Add new remote to channel 3
info on page 8–9
NOTE 3
Pulsed/constant
ground output upon panic
15-second entry delay: on/off
info on page 13
Channel 4 output:
pulsed
, timed, latched
Row 4
4th momentary
Sound 4: on/off
info on page 18
Add new remote to channel 4
info on page 8–9 NOTE 4
FACT: on/off
info on page 15
AutoLock/UnLock: on/off
info on page 18
Channel 5 output:
pulsed, timed, latched
Row 5
5th momentary
Sound 5: on/off
info on page 18
Add new remote to channel 5
info on page 8–9 NOTE 5
Factory-delayed
courtesy lights: on/off
Enhanced AutoArming: on/off
info on page 13
Siren duration: 30/60 seconds
info on page 18
Row 6
6th momentary
Sound 6: on/off
info on page 18
Erase all channels
info on page 8–9 NOTE 6
Set a new secret valet code
info on page 12 NOTE 9
AutoArm & Lock: on/off
info on page 13
NOT USED
Gray cells indicate features that require programming by trained Clifford installers. DO NOT change any of these settings.
✱ WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Changing the duration may cause damage.
✱
NOTE 1:
Transmit channel 1 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 4:
Transmit channel 4 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 5: Transmit channel 5 (or other channel of your choosing) of the new remote
control. You will hear two chirps to indicate that the code has been accepted and
recorded.
NOTE 6: When you hear the two chirps, all remote control codes will have been erased
from system memory. You must now add the new and/or existing remote controls to
the system (i.e., program channels 1–5 of each remote that will be used with your
IntelliGuard 800 system).
NOTE 7:
Turn off the ignition, leave the driver’s window open and exit the vehicle. To
test the current sensitivity, lean into the passenger compartment through the window.
When the sensor detects the intrusion, the system will sound a single confirmation
chirp. To increase the sensitivity setting, press button 2 (you’ll hear higher and higher
confirmation chirps). To decrease sensitivity, press button 4 (you’ll hear lower and
lower chirps). Retest by leaning through the window. When satisfied with the
sensitivity setting, press button 1 to record the new sensitivity level and exit sensor
test/adjust mode (you’ll hear 3 chirps to confirm this). You may now either arm the
system with channel 1 or enter the vehicle.
NOTE 8: Use the same procedure as NOTE 7, but adjust the sensor to detect your
presence when you lean within a foot of the driver’s window.
NOTE 9: Immediately flip the switch to its latched position, then enter the new code
that you wish to use. Make sure to return the switch to its center position when
complete, then wait 3 seconds (you will hear two chirps when the system has accepted
the new code). Turn the ignition off.
VERY IMPORTANT:
You must immediately
test your new secret disarming/valet code
: Turn the ignition on, enter your new code,
then flip the switch to its latched position. The LED will illuminate. If it does not, the
new code you programmed and the one you just entered do not match.
The system has
reverted to the previous code.
NOTE 10: The timer starts as soon as you enable this feature (5 latches, 2
momentaries). When the duration you wish has been reached, press button 1 on the
remote control. You will hear two chirps to confirm the new duration. Channel 4
and/or 5 will have this same duration if one or both of these were set by your installer
to operate as a timed output.
21 22