E-6
(See figure 1 on inside of the front cover.)
Caution: Plug in the amplifier unit and other
equipment after all connections are
completed.
A
: Connect three satellite speakers with a 3 m cord to the
FRONT L, R and CENTER terminals. Connect two
satellite speakers with a 7 m cord to the SURROUND
L and R terminals. Connect the subwoofer to the
SUBWOOFER terminal.
B
: Connect external audio/video units (a personal
computer, a video game player, a portable DVD/CD
player, a video cassette player, etc. which send
playback signals to this system) to these terminals.
Connections
(See figure 2 on inside of the front cover.)
1 INPUT selector button and indicators
Press this button repeatedly to select an input mode
between DIGITAL, 4CH and 2CH. The current mode is
shown by the lighting of the corresponding indicator.
DIGITAL:
Select this mode to reproduce signals received at the
OPTICAL or the COAXIAL terminal on the rear panel.
When both OPTICAL and COAXIAL terminals receive
signals, the signals at the OPTICAL ternminal are
selected.
4CH:
Select this mode to reproduce signals received at the
FRONT and SURROUND terminals on the rear panel
in a 4 channel surround sound mode. (The center
speaker is not used in this mode.)
2CH:
Select this mode to reproduce signals received at the
FRONT terminals on the rear panel in a 2-channel
stereo mode.
2 MODE selector button and indicators
Press this button repeatedly to select the desired
surround mode between DTS, DIGITAL,
PROLOGIC and off. The current mode is shown by the
lighting of the corresponding indicator. When no mode
is selected, no indicator lights up.
DTS:
Select this mode to reproduce an input source with
DTS decoded.
This mode can be selected only when the input signal
is encoded with DTS and the input mode is set to
DIGITAL.
DIGITAL:
Select this mode to reproduce an input source with
Dolby Digital decoded.
This mode can be selected only when the input signal
is encoded with Dolby Digital and the input mode is set
to DIGITAL.
Controls & connectors
Cautions
● When placing the provided AC adapter on the desk, etc.,
be sure to fix the adapter on the desk, etc. to prevent it
from falling. If the adapter falls, it may cause personal
injury or damage to the adapter and/or other equipment.
● The SPEAKER OUTPUT terminals on the rear of the
amplifier unit are special for connecting with the supplied
speakers. Never connect these terminals to an AV amplifier
or a power amplifier, otherwise it may cause not only a
misoperation of this system, but also damage to this
system.
PROLOGIC:
Select this mode to reproduce an input source with
Dolby Prologic decoded.
This mode can be selected only when input signal is
encoded with Dolby Prologic. This mode cannot be
selected when the input mode is set to 4CH.
* If a signal encoded with DTS or Dolby Digital is
inputted with no surround mode selected, the
corresponding indicator lights up dimly.
3 TEST key
Press this button to output a test tone from the
speakers. A test tone is outputted from the front,
center, surround and subwoofer in turn. The test tone is
used for adjusting volume balance among all the
speakers.
* Not all of the speakers output the test tone depending
on the setting of the SPEAKER MODE switch (C).
4 MUTE button and indicator
Press this button to cut off sound output temporarily.
When this function is active, the indicator lights up.
Press this button again to restore sound output.
* Sound output will also be restored by changing the
status of this system between standby and power-on
modes, and changing the input mode or the surround
mode.
5 CENTER level control
This control is used for adjusting the level of sound
outputted from the center speaker. Turn this control
clockwise to increase the level, and counterclockwise
to decrease the level.
6 SURROUND level control
This control is used for adjusting the level of sound
outputted from the surround speakers. Turn this control
clockwise to increase the level, and counterclockwise
to decrease the level.
SR601ENG(9/29)e 00.9.29, 2:34 PM6
