Filter
Top Products
VG-2 Audio/Visual Alerts
Note: You must turn this feature on before it will
d
etect VG-2.
W
hen a VG-2 signal is detected, the detector ‘hides’ its
own radiated signal and becomes undetectable by
t
he VG-2.
Every
30 seconds, the detector checks for a VG-2
signal. If a VG-2 signal is still pre
sent, the unit
continues to hide and repeats the VG-2 alert. If no
signal is detected, t
wo beeps are provided,
indicating an “all clear” condition. During a VG-2
Alert, X, K, and Ka band signals cannot be
received (Reference page 21 for VG-2 information).
See “Menu Mode” for engaging/disengaging VG-2.
Auto Shut Off Mode
Auto Shut Off Mode automatically shuts off the
detector.
The timer is reset:
1
1
.
.
Each time the detector is turned off
2
2
.
.
The optional power cord is unplugged
3
3
.
.
Any button is pressed before the timer has
expired.
The detector will alert you with an audible and
visual warning before it shuts off. This auto off
function can be programmed for the following:
Off, 1, 2, or 3 hours. During this warning you can
reset the timer by pressing any button. If the unit
has automatically turned itself off, press the Power
button to turn the unit back on. You can manually
engage the Auto Shut Off Mode by pressing and
holding the City button until one beep is heard.
See “Menu Mode” for Auto Shut Off timer settings.
OPERATION OPERATION
Stay Alert Feature
The Stay Alert Feature is designed to test a
d
river’s alertness. To engage (when unit is not
a
larming):
•
Press and hold City until a first audible alert is
g
iven. The “
H
H
”
or “
C
C
”
will flash indicating Stay
A
lert is activated.
W
ithin 30-60 seconds an alert is sounded; to
show alert
ness, the driver must press either the
“City”, “Volume”, or “Quiet” buttons within
3
-5 seconds. If a button is pressed within 3-5
seconds, the cycle is repeated.
If a button is not pressed within 3-5 seconds an
alarm sounds and multiple scrolling icons will
appear on the display.
• Press Power to cancel Stay Alert.
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT
operate a vehicle if you are drowsy. During
extended periods of vehicle operation, you should
take frequent breaks. Improper reliance on the Stay
Alert feature may result in vehicle damage,
personal injury or death.
NEVER OPERATE A
VEHICLE IF YOU ARE DROWSY
.
Safety Warning System
™
In communities where Safety Warning System™
transmitters are located, the detector will
receive over 60 messages. When Safety Radar is
detected, the audio alert is given and the
display alternately flashes the “I”, “III” and “II”
icons.
Note: Not all areas have Safety Warning System
™
transmitters.
OPERATION
11 12 13
Menu Mode
E
E
n
n
g
g
a
a
g
g
i
i
n
n
g
g
/
/
D
D
i
i
s
s
e
e
n
n
g
g
a
a
g
g
i
i
n
n
g
g
V
V
G
G
-
-
2
2
:
:
• Press the “Menu” button and release, a single
beep will be heard. The “H” will flash. Press
t
he “Pwr/Dark” button to engage V/L (ON) or
Press the “Quiet/Vol” button to disengage V/L
(Off
).
A
A
u
u
t
t
o
o
S
S
h
h
u
u
t
t
O
O
f
f
f
f
M
M
o
o
d
d
e
e
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
:
:
The Auto Shut Off
feature can be disabled or
c
hanged to 1 hour, 2 hours or 3 hours.
• Press the “Menu” button and release, a single
beep will be heard
• Press and release “Menu” again. The “C” will
flash and the signal strength indicators
represent hours.
• Press the “Quiet/Vol” button will to change
the selection. (I=1 hour, II=2 hours, III=3 hours)
When no signal strength icons are flashing
If no indicator is lit, the feature is disabled.
F
F
l
l
a
a
s
s
h
h
i
i
n
n
g
g
P
P
e
e
r
r
i
i
s
s
c
c
o
o
p
p
e
e
s
s
:
:
The Periscopes can be disabled, remain on or
set to flash while alarming.
• Press and hold the “Menu” button and
release, a single beep will be heard.
• Press and release “Menu” again until the “H”
and “C” icons and the periscopes flash.
• Press the “Quiet/Vol” button will change the
selection (On/Off/Flashing). When no
periscopes illuminated, the feature is disabled.
Press and hold Menu for 3 seconds to exit