Filter
Top Products
OPERATION
Twin Alert Periscope (Pro-68 only)
Whistler’s new Twin Alert Periscope provides an
added attention getting visual alert. The two extra
LED’s flash on and off when the unit alarms to pro-
vide a unique visual alert. This alert can be pro-
grammed, through the Option Select Mode to: 1.
flash for all alarms, 2. remain on, or 3. turn LEDs off
completely.
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door open-
ers, intrusion alarms and other devices which
share frequencies with police radar. Generally, X
band is used for these devices.
• Press City to cancel Highway mode and
engage City.
• Press City again to enter City 1 Mode
• Press City again to enter City 2 Mode
• Pressing City a fourth time cancels City 2
Mode and returns the unit to Highway Mode.
In City Mode, weak speed/safety radar signals
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City 1 and City 2
Modes operate the same as Highway Mode, but
in City 1 Mode, only the X band sensitivity is
lowered. In City 2 Mode, X-band is not detect-
ed.
Caution: Some towns/small cities may still be
using X band radar
. City Modes do not change
the audio alert for laser or VG-2.
OPERATION
Highway Mode
Highway mode provides full audio warnings any
time radar (X, K, Ka, Safety Radar) or laser sig-
nals are detected, and is recommended for
open road driving. ( Highway Mode displays every signal )
For more information on City and Highway
mode, please visit our FAQ page on our web-
site: www.whistlergroup.com
Teach/Tutorial Mode (Pro-68 only)
Provides simulated alerts for each type of signal.
• Press City and Quiet simultaneously and
release.
• Press Power to exit.
Dim/Dark Modes
Dim/Dark Modes reduce the illumination of the
display.
P
P
r
r
o
o
-
-
5
5
8
8
:
:
• Press and hold Power button for 2 seconds to
reduce illumination to a Dim setting.
• Pressing and holding the Power button for 2
seconds a second time engages Dark Mode.
The display illumination is further reduced.
• Pressing and holding the button a third time
restores full illumination to the display.
P
P
r
r
o
o
-
-
6
6
8
8
:
:
• Quickly press the Dark button to access
Dim/Dark settings.
Dim or dark can be engaged during an alert. In
Dark Mode, the display goes dark for as long as
a signal is being detected and for 20 seconds
after, then the display returns to the dimmer
setting.
OPERATION
8910
Auto Quiet Mode
Auto Quiet reduces the selected audio level to
level (1) approximately 5 seconds after a radar or
safety radar signal is detected. The alert for any
new signal within 20 seconds will resume at level
(1). Auto Quiet does not affect VG-2 or laser
alerts.
• Press Quiet/Menu (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Stay Alert Feature
The Stay Alert Feature is designed to test a dri-
ver’s alertness. To engage (when unit is not
alarming) :
• Press and hold City for approximately 2 seconds.
Release button during or immediately after the alert is
given.
The “H” or “C” will flash indicating Stay Alert is
activated. Within 30-60 seconds two beeps are
sounded; to show alertness, the driver must press
either the City, Volume or Quiet button within 3-5
seconds.
If the button is pressed within 3-5 seconds, the cycle is
repeated. If a button was not pressed with in 3-5 seconds,
alarm sounds and the display will flash all LED’s.
• Press Power to exit
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT oper-
ate a vehicle if you are drowsy. During extended
periods of vehicle operation, you should take fre-
quent breaks. Improper reliance on theStay Alert
feature may result in vehicle damage, personal
injury or death. NEVER OPERATE A VEHICLE IF
YOU ARE DROWSY.