Omega Vehicle Security 533i 3 Automobile Alarm User Manual


 
Page 21
To Change a Feature:
Step 5: After accessing the desired feature, within 10 seconds Press &
Release either the transmitter’s Large Upper Button or the Small
Lower Button.
-Pressing the Large Upper Button turns the feature on; the siren
will chirp once and the Status Light will turn on.
-Pressing the Small Lower Button turns the feature off; the siren
will chirp twice and the Status Light will turn off.
To Access and Change further Features:
Step 6: If there are more features to be programmed, within 10 seconds
of the previous action Press & Release the Valet Switch the same
number of times as the next desired feature’s number.
-Again the siren will chirp and the Status Light will flash as many
times as the Valet Switch was pressed to indicate the new
feature number which is now accessed.
-Use the transmitter as described in Step 5 to change the newly
accessed feature as desired.
-Repeat this Step 6 for each additional feature until all features
are programmed.
To Exit Programing Mode:
Step 7: Allow 10 seconds to pass without performing any programming
actions; or, turn the vehicles’s ignition in.
-The siren will sound briefly and the Status Light will go out to
confirm that the system is exiting Programing Mode.
Important Note: Once the system is in Programming Mode, if at any time
10 seconds elapse without programming activity, the system will automatically
exit Programming Mode. To prevent the system from prematurely exiting
Programming Mode, the feature can entered again by pressing the Valet
Switch, or if a feature is accessed, by pressing either of the buttons. Features
can be selected in any order as desired.
The following pages explain each of the programmable features in detail,
including how to program transmitters and how to customize your system’s
SecureCode. Following the features explanation is a convenient feature
programming checklist, which greatly simplifies the feature programming
process.
Page 22
Feature #1 Transmitter Programming Mode
The first level in the programmable features menu is Transmitter Pro-
gramming Mode, by which additional or replacement transmitters can be
programmed to operate the system. It is important to note that when a
transmitter is programmed into the system, the ATV Warning is activated
and all previous transmitter codes in the system’s memory are deleted.
If a third or fourth transmitter is to be added to operate the system, all of
the transmitters must be programmed into system's memory at the same time,
as the first new transmitter code entered will erase the existing transmitter
codes. Therefore, if your system should ever be compromised by the
addition of an unauthorized transmitter, the ATV feature will warn you. By
simply reprogramming all of your transmitters into the system, the
unauthorized transmitter will be erased.
To program a transmitter:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released one time only. The system’s response will be one siren chirp,
and the Status Light flashing one time, pausing, then repeating. Within 10
seconds, press and release the Large Upper Button of the first transmitter.
The system confirms “learning” the transmitter’s code chirping the siren
once. Repeat this action with each transmitter to be programmed. Only the
Large Upper Button of the transmitter needs pressing and release; all of the
other transmitter button’s operations will be learned automatically.
To program a transmitter to a “2nd” or “3rd” system:
Up to three Crime Guard systems may be independently operated using
a single transmitter. To accomplish this, the transmitter’s button functions
are different for each of the vehicles. This prevents Arming or Disarming the
multiple systems simultaneously when all are within range of the transmitter.
To program a transmitter for 2nd or 3rd systems, when programming press
and release either of the small buttons instead of the Large Upper Button. The
system will automatically assign the transmitter’s other functions in a
different order. The following chart shows button function assignment.
THE 533i
3
’s PROGRAMMABLE FEATURES
Arm/Disarm Auxiliary Output #2 Auxiliary Output #3
Large Button Small Button Small Button
Small Button Large Button Small Button
Small Button Large Button Small Button
Only the “Arm/Disarm” button is pressed when programming.