Filter
Top Products
4
FACTORY DEFAULTS
MASTER PROGRAMMING CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123456
ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITS
REQUEST-TO-EXIT OUTPUT RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAIN RELAY
ALARM SHUNT OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DISABLED
FORCED ENTRY OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OUTPUT #3
DOOR AJAR OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OUTPUT #4
MAIN RELAY ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
AUXILIARY RELAY ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
SOLID STATE OUTPUT #3 ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
SOLID STATE OUTPUT #4 ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
DOOR SENSE/INHIBIT INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DOOR SENSE
KEYPAD LOCKOUT OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DISABLED
KEYPAD ACTIVE OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DISABLED
BEEPER SOUNDS WHEN KEY PRESSED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . YES
BEEPER SOUNDS DURING RELAY #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING RELAY #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING OUTPUT #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING OUTPUT #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO
KEYPAD LOCKOUT COUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TRIES BEFORE LOCKOUT
ANTI-PASSBACK TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO ANTI-PASSBACK
AUTO-RELOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ON
BASIC PROGRAMMING
When the AK-2W is in Programming Mode, both indicators will turn
off until programming begins. After a programming option number
is entered the yellow indicator will blink. This shows that the
AK-2W is ready to accept the new programming data. After the
new data entry is complete, the yellow indicator will fl ash while
the data is being stored. The green indicator will light if the data
is accepted. The red indicator will light if any programming data
is entered incorrectly, and the command will have to be fully
re-entered.
Entering Programming Mode
The 6-digit Master Programming Code (default = 123456) is used to enter
Programming Mode.
Press: # 9 # Master Code
Master Code = the current 6-digit Master Programming Code
Exiting Programming Mode
Press: * * #
The red indicator will light after exiting Programming Mode.
☞ NOTE: The AK-2W will automatically exit Programming Mode after two
minutes of inactivity.
Re-entering a Command After a Mistake
If the red indicator lights, signaling an incorrect entry, or an incorrect key is
pressed during programming, to clear the keypad and re-enter the command:
Press: * 9 #
Setting Entry Code Length Default: 4 digits
Press: 0 3 # Length #
Length = 1 - 6 for entry code length
☞ NOTE: If the Entry Code Length is going to be changed from the factory
default of four digits, make this change fi rst, before programming any
entry codes.
Adding a New Entry Code
Press: 0 1 # Code # Code # Relay #
Code = The new entry code: 1-999999, depending on code length
Relay = Relay output entry code will activate:
1 = Main Relay 2 = Auxiliary Relay 3 = Both Relays
The yellow indicator will fl ash quickly while the AK-2W searches its memory for
available space and duplicate entries. The green indicator will light when the new
code is stored.
If the new entry code chosen is already being used for another entry code, the
red indicator will light. A new unique code needs to be entered.
☞ NOTE: Leading zeros (zeros before the code number, i.e. 0001) do not need
to be entered when programming a new entry code. The AK-2W will internally
add any zeros to fi ll all digits determined by the entry code length setting.
Leading zeros will have to be entered by the user when entering their code
to gain access.
Erasing a Single Entry Code
Press: 0 2 # Code # Code #
Code = The entry code to delete.
The yellow indicator will fl ash quickly while the AK-2W searches its
memory for the code to erase. The green indicator will light when
the code is erased.
Erasing All Entry Codes
★ WARNING: PERFORMING THIS COMMAND WILL
REMOVE ALL ENTRY CODES FROM THE MEMORY.
Press: 9 7 # 0 0 0 0 0 0 # 0 0 0 0 0 0 #
☞ NOTE: The green indicator will light while the memory is being erased. This
may take up to 15 seconds.
Changing the 6-Digit Master Programming Code
Press: 9 8 # Master Code # Master Code #
Master Code = The new 6-digit Master Programming Code
New master code: _____________________
PROGRAMMING OPTIONS
There are several AK-2W programming options. For most
installations, the factory set default options are suffi cient. The
keypad must be in Programming Mode to make these changes.
PROGRAMMING AK-2W TO HOLD THE OUTPUT
Linear’s AccessKey products have a programmable “Toggle Mode”
available for each relay and solid-state output. When an output is
programmed for Toggle Mode, the output alternates from OFF to
ON or from ON to OFF each time it is activated.
The rules for a toggle output are:
• If the output is OFF, it will turn ON and stay on until the next
activation.
• If the output is ON, it will turn OFF and stay off until the next
activation.
Typical Programming
With the unit in Program Mode, set the Auxiliary Relay (Relay #2)
output to Toggle Mode using the following keystrokes:
Press: 2 2 # 9 9 #
22 = Programming Step; 99 = Toggle Mode
222162 B IMAGE 6