Filter
Top Products
FACTORY DEFAULTS
MASTER PROGRAMMING CODE. . . . . . . . . . . . . . . . . . . . 123456
ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITS
REQUEST-TO-ENTER OUTPUT . . . . . . . . . . . . . . . . . . RELAY #1
ALARM SHUNT OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . DISABLED
FORCED ENTRY OUTPUT . . . . . . . . . . . . . . . . . . . . . OUTPUT #3
DOOR AJAR OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . OUTPUT #4
RELAY #1 ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
RELAY #2 ON TIME . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECONDS
SOLID STATE OUTPUT #3 ON TIME . . . . . . . . . . . . 2 SECONDS
SOLID STATE OUTPUT #4 ON TIME . . . . . . . . . . . . 2 SECONDS
DOOR SENSE/INHIBIT INPUT. . . . . . . . . . . . . . . . DOOR SENSE
KEYPAD LOCKOUT OUTPUT . . . . . . . . . . . . . . . . . . . . DISABLED
KEYPAD ACTIVE OUTPUT . . . . . . . . . . . . . . . . . . . . . . DISABLED
DOWNLIGHT ON-TIME. . . . . . . . . . . . . . . . . . . . . . . . . 2 MINUTES
BEEPER SOUNDS WHEN KEY PRESSED . . . . . . . . . . . . . . YES
BEEPER SOUNDS DURING RELAY #1 . . . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING RELAY #2 . . . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING OUTPUT #3. . . . . . . . . . . . . . . . . NO
BEEPER SOUNDS DURING OUTPUT #4. . . . . . . . . . . . . . . . . NO
KEYPAD LOCKOUT COUNT . . . . . 3 TRIES BEFORE LOCKOUT
ANTI-PASSBACK TIME . . . . . . . . . . . . . . . . NO ANTI-PASSBACK
BASIC PROGRAMMING
When the AK-11 is in programming mode, both LEDs will turn off
until programming begins. After a programming option number
is entered the yellow LED will blink. This indicates that the AK-11
is ready to accept the new programming data. After the new data
entry is complete, the green LED will light while the data is being
stored. The red LED will light if any programming data is entered
incorrectly, and the command will have to be fully re-entered.
Entering Programming Mode
The 6-digit Master Programming Code (default = 123456) is used
to enter Programming Mode.
Press:
#
9
#
Master Code
Master Code = the current 6-digit Master Programming Code
Exiting Programming Mode
Press:
*
*
#
The red LED will light when Programming Mode is exited.
☞NOTE: The AK-11 will automatically exit Programming Mode
after two minutes of inactivity.
Re-entering a Command After a Mistake
If the red LED lights, indicating an incorrect entry, or a wrong key
is pressed during programming, to clear the keypad and re-enter
the command:
Press:
*
9
#
Setting Entry Code Length Default: 4 digits
Press: 0 3
#
Length
#
Length = 1 - 6 for entry code length
☞NOTE: If the Entry Code Length is going to be changed from
the factory default of four digits, make this change first, before
programming any entry codes.
Adding a New Entry Code
Press: 0 1
#
Code
#
Code
#
Action
#
Code = The new entry code: 1-999999, depending on code length
Action = Relay output entry code will activate as follows:
1 = Relay #1, timed open
2 = Relay #2, timed open
3 = Both Relays, timed open
10 = Relay #1, toggled
20 = Relay #2, toggled
30 = Both Relays, toggled
12 = Relay #1 toggled; Relay #2, timed open
21 = Relay #1, timed open; Relay #2 toggled
The yellow LED will flash quickly while the AK-11 searches its
memory for available space and duplicate entries. The green
LED will light when the new code is stored.
If the new entry code chosen is already being used for another
entry code, the red LED will light. A new unique code needs to
be entered.
☞NOTE: Leading zeros (zeros before the code number, i.e.
0001) do not need to be entered when programming a new
entry code. The AK-11 will internally add any zeros to fill all
digits determined by the entry code length setting. Leading
zeros will have to be entered by the user when entering their
code to gain access.
Erasing a Single Entry Code
Press: 0 2
#
Code
#
Code
#
Code = The entry code to delete.
The yellow LED will flash quickly while the AK-11 searches its
memory for the code to erase. The green LED will light when the
code is erased.
Erasing All Entry Codes
★ WARNING: Performing this command will remove
all entry
codes from the memory.
Press: 9 7
#
0 0 0 0 0 0
#
0 0 0 0 0 0
#
☞NOTE: The green LED will light while the memory is being
erased. This may take up to 15 seconds.
Changing the 6-Digit Master Programming Code
Press: 9 8
#
Master Code
#
Master Code
#
Master Code = The new 6-digit Master Programming Code
New master code: _____________________
6