Filter
Top Products
Page 7 of 9
4. NEUTRRAL SAFETY SWITCH
Your vehicle should starts only in Parked or in
Neutral position with the key. If the vehicle starts
in any other position, the Manual Transmission
Mode has to be activated. (Consult your
dealer).
5. ALARM TRIGGER
Your alarm will be triggered in the following ways:
A. Light Impacts will trigger the 1
st
stage of the
Shock Sensor, the siren will chirp 4 times and the
parking lights will flash for a few seconds. The
LCD will not show anything for 1
st
stage of the
Shock Sensor.
B. Heavy impacts will trigger the system with 30
Sec. of constant siren and flashing of the parking
lights. The Hammer in the LCD will show up and
flash 6 times if it is in the Paging Mode.
C. If a Door is opened, the siren will go off and
the parking lights will flash for 30 Sec. The door
in the LCD will flash 30 times if it is in the Paging
Mode.
D. Optional starter kill prevents the vehicle’s
starter from cranking.
6. TRANSMITTER LEARNING PROCEDURE
Steps 1: Put the system in Valet mode with key:
Ignition On and Off Three times with key within 3
Sec. The parking light will flash once, when it
enters the Valet Mode.
Step 2: Once in the Valet Mode, within 6 Sec.
choose one of the Lock options by pressing:
Button I for ½ Sec. for normal locks.
Button II for 2 Sec. for double pulse unlock
Button III for 2 Sec. for lock pulse after Ignition
turns Off for those vehicles that has factory
Ignition control Door Lock and Unlocks the Door
when the Ignition is turned Off.
Button IV for ½ Sec. for 4-second door lock
pulse.
The parking light will flash twice to confirm step 2.
Step 3: Program 2
nd
remote or 3
rd
remote by
pressing any button. The system will program up
to 3 remotes. The parking light will flash once to
confirm step 3.
Note: Step 3 will remove any of the previous
programming of the remotes. Each time when
you program a remote, you have to program the
2
nd
or 3rd remote also even if it was programmed
previously.
7. PROGRAMMING OPTIONS WITH REMOTE:
Step 1: Place the key in the Ignition, and turn to
the ON potion (vehicle not running.) (This means
that there should be 12v at IG1 and nothing at
the Tach sensing wire or Alternator sensing
wire.)
Step 2: Press the buttons I and IV for ½ Sec. The
siren will chirp once, now you are in the
Programming Mode.
Step 3: Option 1- Ignition Lock (locks all doors
after starting.)
Press button I for ½ Sec. to select Option 1.Press
button IV for ½ Sec. to not select Option 1.
(Two chirps, confirming step 3.)
Step 4: Option 2- locks all doors after
reservation (Manual Transmission only).
Please go over the procedure for Reservation
Mode for the Manual transmission. If you choose
Option 2, the doors will lock when you exit the
vehicle and close the door.
Option 2 is recommended.
Press button I for ½ Sec. to select Option 2.
Press button IV for ½ Sec. to not select Option2.
(Three chirps, confirming Step 3.)
Step 5: Option 3- A. (Passive Arming) After
the last door is closed the system will chirp every
10 seconds and Arm itself after 3 warning chrips.
Press Button I for ½ Sec.
Option 3- B. (Semi-passive arming) The
system will Arm itself after disarm like Option 3-A,
except if a door has been opened after disarm,
the system will not Passively arm. Press Button
II for 2 Sec.
Option 3- C. (Active arming) System wills
arm/disarm only by the remote. Press Button IV
for ½ Sec.
(Four chirps, confirming step 5.)
Step 6: Option 4-A. If you enter 24Hr mode, the
system will start the vehicle every hour. Press
Button I for ½ Sec.
Option 4- B. In 24Hr mode, every 2 hour. Press
button II for 2 Sec.
Option 4- C. In 24Hr mode, every 3 hour. Press
Button III for 2 Sec. Option 4-D. Not to program
24Hr Mode. Press button IV for ½ sec Five
chirps, confirming step 6.
NOTE: Go through the procedures Step by Step.
If the system dose not give the confirmation
chirps, go through the Programming Option
again.