Filter
Top Products
Page 4 of 9
1. OPERATION: REMOTE FUNCTIONS FOR
AUTOMATIC TRANMISSON
Please take time to read the owners manual. If
you have any question, please contact your
authorized dealer.
Also, refer to the FUNCTION printed on the back
of your remote.
Button I. Press ½ Sec.
Arm(Lock)/Disarm(Unlock)
If there is no response, you are
out of range.
All doors have to be closed: if
not, the door in the LCD will flash.
Factory setting: No ignition locks, Active
Arming. The status LED will begin to flash after
3 seconds upon locking the doors. The Starter
Kill (Optional feature, see your dealer) will take
into effect. The shock sensor will be in Impact
Watch Mode for 30 seconds upon arming.
Upon disarming, if siren chirps more than two
times, the system has been triggered while
armed: 3 chirping by Shock sensor, 4 chirping
by Door sensor. Note: The system also can be
programmed for Passive Arming. The system
will check the doors, and if the doors are all
closed, the system will arm itself in 30 seconds.
If the vehicle has a dome light delay circuit and
you have to wait until the dome lights go off
before you Arm(Lock) the car, consult your
authorized dealer about Passive Arming.
Warning: Do not press Button
I for more than ½ Sec. (See next)
Button I. Press 2 Sec. Panic
To turn off Panic, press Button
I for ½ second.
Panic is also a Car Finder.
Button II. Press 2 sec. Remote
Start/Stop
Running time: 15 or 25 minutes
(24/45 for diesel). Factory
setting is 25minutes(45 for
diesel). If there is no response,
you are out of range.
If the door in the LCD flashes, check to see if a
Door is open, the Hood is open, the by-pass
switch is On or the Brake pedal is being pressed.
The vehicle will remain running for until,
Programmed time elapsed, Button II pressed for
2 seconds, Break Pedal pressed, Hood opened,
or By-Pass Switch turned On.
Button III Press 2 Sec. Trunk
Release (optional see dealer)
When the Button III is pressed
for 2 Sec., the trunk will open
and the system will also
Disarm/Unlock the doors as
well.
Button IV Press ½ Sec. Query
The LCD will show the status
of your vehicle.
Note: Nothing will happen if
the Button IV is pressed more than ½ Sec.
The LCD in the remote displays 5 different
Modes.
Button I+II Press ½ sec. Mute
Mode (On/Off)
When the Mute Mode is Off
when SPK is indicated in the LCD.
Button I+III Press ½ Sec. Valet
Mode (On/Off)
Valet Mode will shut down the
alarm and the remote starter
system. Only the Lock/Unlock
will work in valet mode. The
Valet Mode can also be
entered with the KEY. Turning
KEY to ON from ACC three
times within 3 seconds.
Note: The LCD will not display
the Zz. when the KEY is used
to enter the Valet Mode. Press
Button I+III to exit Valet Mode.
Button II+III Press ½ Sec. Car Call/
Paging mode (On/Off)
Your remote will be paged
when your vehicle is being
tampered with. The LCD will
tell you whether it was
tampered by Impact Sensor
(hammer flashing) or Door
being opened (door flashing).
You will save the battery by
turning Off the Paging mode.
CAR CALL will indicate in the
LCD when this mode is on.
Note: The Pager will not
respond to the first stage of the
Shock Sensor.
Button II+IV Press ½ Sec. 24Hr.
Timer Mode (On/Off)
Your car will automatically start
every One, Two or Three
Hours. Factory Setting: 3 hrs.
If you want to change the
Factory Settings, see
programming section.