Filter
Top Products
Page 5 of 9
Button III+IV Press ½ Sec. Turbo
Mode (2
nd
car on/off)
Control Two vehicles with One
Remote. Why is it called
Turbo? This mode is used in
different ways in other
countries. Factory Setting: The
remote control has been
programmed to work either
Turbo On /Off indicated in the
LCD.
Note: If you want to program
more than one remote to a
vehicle, every time you
program a remote, you must
program the 2
nd
and 3
rd
remote
at the same time. Up to three
remotes to a vehicle.
2. OPERATION: REMOTE FUNCTIONS FOR
MANUAL TRANSMISSION
Please take time to read the owners manual. If
you have any question, please contact your
authorized dealer.
Also, refer the FUNCTION printed on the back
Button I. Press ½ Sec.
Arm(Lock)/Disarm(Unlock)
If there is no response, you are
out of range.
All doors have to be closed: If
not, the door in the LCD will flash.
Factory setting: No ignition lock, Automatic
Arming(Lock) upon completion of reservation
and Active Arming. The status LED will begin to
flash after 3 seconds upon locking the doors.
The Starter Kill (Optional feature, see your
dealer) will take into effect. The shock sensor
will be in Impact Watch Mode for 30 seconds
upon Arming. Upon Disarming, if siren chirps
more than Two times, the system has been
triggered while armed. 3 chirping by Shock
sensor, 4 chirping by Door sensor. If the vehicle
has a dome light delay circuit and you have to
wait until the dome lights go off before you
Arm(Lock) the car, consult your authorized
dealer.
Note: Passive Arming. The system also can
be programmed for Passive Arming. The
system will check the doors. If the doors are all
closed, the system will arm itself in 30 seconds.
Warning: Do not press Button I
for more than ½ Sec. (See next)
Button I. Press 2 Sec. Panic
To turn off Panic, press Button
I for ½ second.
Panic is also a Car Finder.
Button II. Press 2 sec. Remote
Start/Stop
Running time: 15 or 25 minutes
(24/45 for diesel). Factory
setting is 25minutes(45 for
diesel). Also, the factory setting
is automatic Arming(Lock)
upon completion of reservation.
If there is no response, you are
out of range.
If the door in the LCD flashes without starting the
vehicle, when the Reservation Mode has not
been set. Also, check to see if a Door or the
Hood is open, the by-pass switch On or the
Parking Break released. The vehicle will remain
running for until; Programmed time has elapsed,
Button II pressed for 2 seconds, Parking Brake
released, Hood opened, or by-pass Switch turned
On.
IMPORTANT
1. The vehicle must be in the
NEUTRAL position.
2. The vehicle windows must be rolled
up.
3. Do not set the reservation mode
with any people in the vehicle.
4. Do not remote start with any people
in the vehicle.
Note: The system is not recommended for
vehicle with removable tops.
Reservation Mode must be set for Manual
Transmission vehicles to Remotely Start.
Steps1: After arriving at the destination, and
before turning the engine OFF, shift the
transmission to the Neutral position.
Step 2: Activate your parking brake.
Step 3. Remove the key from the ignition. The
engine will remain running.
Step 4. Exit the vehicle and close the door
within Two minutes from step 3. Then, the
engine will shut Off and Reservation Mode is
now complete.
Your vehicle is now ready for remote starting.
However, the reservation mode will be cancelled
if Door has been opened or CompuStar has been
put in Valet mode after Step 4, in which cases
you have to start the vehicle with the key and
repeat the above 4 steps if you want to restore
the Reservation Mode.