Filter
Top Products
34
M475
English
TV Operations
TV tuner functions
When an optional TV tuner (additional TTX7501Z
CeNET module required) is connected through the
CeNET cable, this unit controls all TV tuner functions.
To watch TV requires a TV tuner and monitor.
Watching a TV
1.
Press the [
SRC
] button and select the TV mode.
2. Press the [BND] button to select the desired
TV band (TV1 or TV2). Each time the button
is pressed, the input selection toggles
between TV1 and TV2.
3. Press the [R] or [F] button to tune in the
desired TV station.
Tuning
There are 3 types of tuning modes available,
seek tuning, manual tuning and preset tuning.
Seek tuning
1. Press the [BND] button and select the desired
TV band (TV1 or TV2).
* If “MANU” is lit on the display, press and hold
the [BND] button for 1 second or longer.
“MANU” on the display goes off, and seek
tuning is now available.
2. Press the [R] or [F] button to
automatically seek a station. Press the [F]
button to automatically tune up the frequency
band to the next available TV station; press
the [R] button to automatically tune down.
Manual tuning
There are 2 manual tuning methods available:
Quick tuning and step tuning.
When you are in the step tuning mode, the
frequency changes one step at a time. In the
quick tuning mode, you can quickly tune the
desired frequency.
1. Press the [BND] button and select the desired
band (TV1 or TV2).
* If “MANU” is not lit on the display, press and
hold the [BND] button for 1 second or longer.
“MANU” lights on the display and manual
tuning is now available.
2. Tune in a station.
●Quick tuning
Press and hold the [R] or [F] button for 1
second or longer to tune in a station.
●Step tuning
Press the [R] or [F] button to manually tune
in a station.
Recalling a preset station
A total of 12 TV stations can be stored (6-TV1
and 6-TV2). This allows you to select your
favorite TV stations and store them in memory for
later recall.
1. Press the [BND] button and select the desired
TV band (TV1 or TV2).
2. To recall a stored TV station, press the
desired [DIRECT] button or the [E]/[e] button
to select that station.
* Press and hold one of the [DIRECT] buttons for
2 seconds or longer to store the current station
into preset memory.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
2. Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into preset memory.
Auto store
Auto store selects 6 TV stations automatically
and stores each one into preset memory.
If there are not 6 stations with good reception,
stations previously stored in memory remain and
only the strong stations are stored into memory.
1. Press the [BND] button and select the desired
TV band (TV1 or TV2).
2. Press and hold the [ ] button for 2 seconds
or longer. The stations with good reception
are stored automatically to the preset
channels.
Preset scan
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for a desired TV station in memory.
1. Press the [ ] button.
2. When the desired station is found, press the
[ ] button again to remain tuned to that
station.
Note:
• Do not press and hold the [] button for 2
seconds or longer. Doing so will trigger the auto
store function and start storing stations into
memory.
Setting TV/VTR and TV diver
To switch TV to VTR, to select the TV area, and
to set the TV diver, see “Common Operations”.
M475.book Page 34 Thursday, December 21, 2006 4:08 PM