Autostart AS-2272 Remote Starter User Manual


 
Installation Guide P. 17
FEATURE 4 – Door lock pulse timing
OPTION 1* 7/10-sec. lock / unlock pulses
OPTION 2 4-sec. lock / unlock pulses
OPTION 3 7/10-sec. lock pulse and two 1/4-sec. unlock pulses
FEATURE 5 – LED flashing
OPTION 1* ENABLED (without starter kill Æ will flash only when ignition is OFF)
OPTION 2 DISABLED
OPTION 3 ENABLED (with starter kill Æ will ONLY flash when the starter kill engages.
This option should be selected ONLY if the starter kill is installed.)
FEATURE 6 – Bypass
OPTION 1* Trilogix
OPTION 2 ADS
OPTION 3 Fortin
FEATURE 7 – Bypass Type
OPTION 1* Two-Way communication
OPTION 2 One-Way communication
MENU 2
* INDICATES DEFAULT SETTING
FEATURE 1 – Engine Run Time
OPTION 1 Run Time = 3 minutes in gas mode / 8 minutes diesel mode
OPTION 2* Run Time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3 Run Time = 25 minutes in gas mode / 30 minutes diesel mode
FEATURE 2 – Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1 Idle mode & turbo mode DISABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 2* Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 3 Idle mode & turbo mode ENABLED (AUTO) / turbo mode ENABLED (MANUAL)
FEATURE 3 – Engine type and Cold Weather Mode
OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2* Gas mode with 3-minute run time in cold weather mode
OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
FEATURE 4 – Lock / unlock or horn output (when Menu 2, Feature 6, Option 1 is programmed)
OPTION 1 N/A
OPTION 2* Constant output when button Ι is pressed > 3 sec. (first press will give a (-) output
on LOCK wire; second press will give a (-) output on UNLOCK wire)
OPTION 3 Horn confirmation upon the 1
st
press of the LOCK button.
FEATURE 5 – Pager (Pager sold separately)
OPTION 1 Pager ENABLED
OPTION 2* Pager DISABLED
FEATURE 6 – Remote Functions
OPTION 1 Button Ι = Lock/Unlock, Button ΙΙ = Start/Stop, Button Ι & ΙΙ = Trunk
OPTION 2* Button Ι = Stop, Button ΙΙ = Start, Button Ι & ΙΙ = Trunk
FEATURE 7 – Ready Mode Option
OPTION 1 Enabled by handbrake
OPTION 2* Enabled by remote
Virtual Tach System
* Virtual Tach System combines the latest microcontroller technology and a complex algorithm
that took years to develop. VTS is able to effectively monitor the engine starting sequence and
release the starter at the right time without physically connecting the tach wire to the remote
starter. The VTS constantly monitors the data and readjusts itself automatically in order to
maximize its capability to start the engine properly in any weather or deteriorating battery condition
(automatic transmission only).
Optional Time Delay Adjustment in Virtual Tach System
Follow these steps to program crank time adjustment, if needed:
1. Enter programming mode (see on page 14) the parking lights will stay on for up to 20
seconds.
2. Before the lights go out, press and hold the brake pedal and press the Ι and ΙΙ buttons
simultaneously the parking lights will flash 4 times. Do not release the brake pedal.