Filter
Top Products
128-6199
6 of 8
Page 6
2 Pin Blue Connector : VALET PUSH-BUTTON SWITCH
Route the grey and black wires in the 2 pin connector from the valet switch to the control module, and plug it into the mating blue
connector on the side of the module.
2 Pin White Connector : DASH MOUNTED LED
Route the red and blue wires in the 2 pin white connector from the LED to the control module and plug it into the mating white
connector on the side of the module.
4 Pin White Connector : SHOCK SENSOR
Route the red, black, blue, and green wires in the 4 pin white connector from the shock sensor to the control module and plug one end
into the shock sensor, and the other end into the mating white connector on the side of the module.
Red / Green / Red w/Black Trace 3 Pin White Connector : Door Lock Outputs
The Red and Green wires will provide either a pulsed ground output to the factory door lock control relay or a pulsed + 12 volt output
to the factory door lock control relay. In either case, the maximum current draw through these outputs must not exceed 300 mA. The
Red w/Black trace wire will provide a pulsed ground only, and will only provide an output when the unlock button of the transmitter is
pressed a second time after a first unlock command was issued. This is used for second step unlock or all doors unlock in a two step
circuit. In this arrangement, Red is used to control the drivers door unlock relay and the Red/Black will be used to control unlock of
all other doors.
3 Wire Ground Switched Single Step Door Locks
In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red
wire to the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.
The green wire provides a ground pulse during disarming, or the pulsed ground unlock output. Connect the green wire to
the wire that provides a low current ground signal from the factory door unlock switch to the factory door lock control relay.
Red/Black Not Used.
3 Wire Ground Switched 2 Step Door Locks
In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red
wire to the wire that provides a low current ground signal from the factory door lock switch to the factory door lock control relay.
The green wire provides the first ground pulse during disarming, or the drivers door pulsed ground unlock output.
Connect this wire to the drivers door unlock relay that requires a low current ground signal to unlock only the drivers door.
If the vehicle does not have a separate drivers door relay, one will have to be added. Locate the drivers door unlock motor wire
and cut it at a convenient location to allow wiring of an optional relay. Connect the door side of the cut wire to terminal 30 of the
optional relay added. Connect the vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the green
wire of the 3 pin harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to a fused
constant + 12 volt source. Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door lock/unlock
motor legs for operation, if this is the case in the vehicle you are working on, connect the remaining terminal, 87, to a fused + 12
volt source. In the rare instance that the vehicle door lock/unlock motor legs rest at + 12 volts and switches ground to the door
lock/unlock motors, connect he remaining terminal, 87, to chassis ground.
The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time after
disarming. Connect the Red/Black wire to the wire that provides a low current ground signal from the factory door unlock
switch to the factory door lock control relay.
3 Wire Positive Switched Door Locks
In this application, the red wire provides a positive pulse during disarming, or the pulsed + 12 volt unlock output. Connect the
red wire to the wire that provides a low current positive signal from the factory door unlock switch to the factory door lock
control relay.
The green wire provides a positive pulse during arming or the pulsed + 12 volt lock output. Connect the green wire to the wire that
provides a low current positive signal from the factory door lock switch to the factory door lock control relay. Red/Black Not Used.
3 Wire Positive Switched 2 Step Door Locks
The green wire provides a positive pulse during arming or the pulsed + 12 volt lock output. Connect the green wire to the wire that
provides a low current positive signal from the factory door lock switch to the factory door lock control relay.