Filter
Top Products
Mode Tone Visual Setting
Result
VG-2 Detect
mode
Two beeps VG-2 Detect On Unit will detect VG-2 signals.
One beep VG-2 Detect Off Unit will not detect VG-2 signals.
VG-2 Audio
mode (not
shown if VG-2
detect is Off)
Two beeps VG-2 Audio On With VG-2 Detect On, the unit will give
audible alerts for VG-2 signals.
One beep VG-2 Audio Off With VG-2 Detect Off, the unit will give
only visual alerts for VG-2 signals.
Spectre
Detect mode
Two beeps Spectre
Detect On
Unit will detect Spectre I & IV+ signals.
One beep Spectre
Detect Off
Unit will not detect Spectre I & IV+
signals.
Spectre
Audio mode
(not shown
if Spectre
detect is Off)
Two beeps Spectre Audio
On
With Spectre Audio On, unit will give
audible alerts for Spectre signals.
One beep Spectre Audio
Off
With Spectre Audio Off, unit will give only
visual alerts for Spectre signals.
SmartPower
mode
Two beeps SmartPower On SmartPower is On.
One beep SmartPower Off SmartPower is Off.
X Band
Detect mode
Two beeps X Band On Unit will detect X Band signals.
One beep X Band Off Unit will not detect X Band signals.
K or Ku Band
Detect mode
Two beeps K or Ku Band On Unit will detect K or Ku Band signals.
One beep K or Ku Band Off Unit will not detect K or Ku Band signals.
Set display
Dim mode
default*
Two beeps Display Dim Partially dimmed for dusk or night driving.
One beep Display Dimmer More dimmed for dusk or night driving.
One beep Display Dark Display is Off.
Restore factory
settings
One beep Restore Factory
Settings
Resets user modes and settings to
factory default.
Exit program One beep EXIT PROGRAM Allows you to exit Program mode.
* The settings for these user modes can also be changed
with the one button method. See description of each
user mode (pages 10 and 24) for details.
EasySet Programming Menu
9
EasySet Programming Menu
Your Detector Your Detector
Mode Tone Visual Setting Result
Set
IntelliShield
City mode
default*
Two beeps City X A single beep sounds when the
signal is first detected.
One beep City X
beep Off
Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One beep City X+K Combines the City X mode with
prevention of K band audio alerts
until signal strength reaches Level 2.
IntelliMute
mode
Two beeps IntelliMute On All alerts (except for strobe signals
from emergency vehicles) are
automatically muted below the
engine rev point you set.
One beep IntelliMute Off Normal operation.
Set
IntelliMute
RPMs
One beep Set IntelliMute
(see page 14
to set activation
point)
Allows you to set the engine
rev point while using IntelliMute.
Note: Only shown if IntelliMute is Off.
IntelliMute
Pro mode
Two beeps IntelliMute Pro
On
All radar, VG-2 and Spectre detection is
turned Off below the engine rev set point.
One beep IntelliMute Pro
Off
Normal operation.
AutoMute
mode
Two beeps AutoMute On The audio volume of all alerts will be
automatically muted after four seconds for
as long as the signal is detected.
One beep AutoMute Off All alerts will sound at full volume
for as long as the signal is detected.
Set
compass
One beep Set Compass Allows you to calibrate the compass.
(see page 17 to calibrate compass)
Pop Detect
mode
Two beeps Pop Detect On Unit will detect Pop signals.
One beep Pop Detect Off Unit will not detect Pop signals.
This EasySet Programming menu lists all of the modes and settings you can
choose from after you have entered Program mode as described on page 7.
8
English
Nothing Comes Close to a Cobra
®
XRS9670_MANL_A.indd 8-9 8/30/10 8:37 AM