Table of user-selectable features: 1 chirp = OFF, two chirps = ON.
Feature Select
Column 1
1st latched
Column 2
2nd latched
Column 3
3rd latched
Column 4
4th latched
Row 1
1st momentary
Sound 1:
on
/off
info on page 18
Add new remote to channel 1
info on page 10 NOTE 1
AutoLock
on
/off
info on page 16
AutoArming:
on
/off
info on page 12
Row 2
2nd momentary
Sound 2: on/off
info on page 18
Add new remote to channel 2
info on page 10
NOTE 2
AutoUnLock on/off
info on page 16
AutoArm & Lock: on/off
info on page 12
Row 3
3rd momentary
Sound 3: on/off
info on page 18
Add new remote to channel 3
info on page 10
NOTE 3
FACT: on/off
info on page 15
15-second entry delay: on/off
info on page 11
Row 4
4th momentary
Sound 4: on/off
info on page 18
Add new remote to channel 4
info on page 10 NOTE 4
AutoActivate timed accessory
upon remote arming: on/off
this feature is for installers only
✱ Set headlight duration
1sec - 2min (
30sec
)
info on page 10 NOTE 6
Row 5
5th momentary
Sound 5:
on
/off
info on page 18
Erase all channels
info on page 22 NOTE 5
QuietChirps: on/
off
info on page 18
Siren duration: 60/
30
seconds
(1/2 chirps) info on page 18
Row 6
6th momentary
Sound 6:
on
/off
info on page 18
Headlight Reminder:
on
/off
info on page 16
Long-term chirp silencing: on/
off
info on page 18
Set a new secret valet code
info on page 14 NOTE 7
✱ WARNING: If you have remote window and sunroof closure,
DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Changing the duration may cause damage.
Please Note: There is a column 5 that contains installer-only features; do not change any of these settings. If you accidentally select column 5, turn off the ignition.
NOTE 1:
Transmit channel 1 (or other channel of your choosing) of the new
remote control. You will hear one chirp to confirm programming of channel 1.
NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new
remote control. You will hear two chirps to confirm programming of channel 2.
NOTE 3:
Transmit channel 3 (or other channel of your choosing) of the new
remote control. You will hear three chirps to confirm programming of channel 3.
NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new
remote control. You will hear four chirps to confirm programming of channel 4.
NOTE 5:
When you hear one chirp, all remotes will have been erased from the
system memory. You must now add the new and/or existing remote controls to
the system (i.e., program channels 1–4 of each remote that will be used with
your IntelliGuard 700-IQ).
NOTE 6:
The headlight timer starts as soon as you select this feature. When the
duration you wish has been reached, press button 1 on the remote control. You
will hear two chirps to confirm the new headlight timer duration.
NOTE 7: Immediately flip the switch to its latched position
, then:
a. Enter the new code you wish to use. The system will sound the same number of
chirps as the digit you choose when you move the switch to the latched side (e.g.,
if the first digit is 4, you’ll hear four chirps when you press the latched side).
b. Make sure to return the switch to its center position when complete.
c.
Wait 3 seconds until you hear 2 chirps
, indicating the new code has been
accepted.
d. Turn the ignition off. You’ll hear 3 chirps to confirm program mode exit and
the LED will turn off.
e. VERY IMPORTANT: You must immediately test your new secret valet
code: Turn the ignition on, enter your new code, then flip the switch to its
latched position. The LED will illuminate. If it does not, the new code you
programmed and the one you just entered do not match. The system has
reverted to the previous code.
23 24
for IG700IQ owners
© Copyright Clifford Electronics, Inc., 1995 31-711B/IG7OM/1195