Filter
Top Products
How to set your own valet/disarming PIN code
Your secret valet/disarming PIN code will be used to deactivate BlackJax, enter valet mode and ente r programming mode. You may choose any 1-4-digit
PIN code, but the first digit must not be a zero (e.g., 1023 is a valid code, 0123 is not). See User-selectable features. Let’s say you want to set a PIN code of 4301:
1. From the Table of user-selectable features, you would note that the Set a new secret valet/disarming PIN code feature is in column 2, row 7.
2. Enter program mode by turning on the ignition, entering your current code, then pressing and holding the ✱ button of the PlainView 2 switch for 3
seconds until you hear a chirp.
3. Select column 2 by pressing the blank button twice. After a brief pause, you will hear 2 chirps to confirm that you have selected feature column 2.
4. Within 5 seconds, select row 7 by pressing and releasing the ✱ button 7 times. To help you count, you will hear a chirp each time you press the ✱
button. After 7 presses, immediately press the blank button, then immediately enter your new code.
Example: To enter 4301 as your new code, you would press the switch buttons in this manner: ✱✱✱✱ blank, ✱✱✱
blank, blank, ✱ blank.
5.Wait for the 2-chirp confirmation.
6. Turn off the ignition to exit program mode (you’ll hear a 3-chirp confirmation).
7. VERY IMPORTANT: You must immediately test your new valet/disarming PIN code: Turn on the ignition, enter your new code, then press and
hold the blank button for 4 seconds. The LED will illuminate to indicate that the system is in valet mode. Turn the ignition off. The sy stem is now in valet
mode.
If the LED does not illuminate, the new code you programmed and the one you just entered do not match. In such a
case, the system will revert to the previous code.
8.To exit valet mode and return to normal operation, turn the ignition on and enter your code.
Your re mote con trols
The 5-button master remote control and the 4-button companion remote are sophisticated miniature ra dio transmitters each powered by a tiny battery
(12-volt alkaline for the master remote, a 3-volt lithium battery for the companion remote). A weak remote control battery will reduce range (the system
will warn you if the battery in your remote is nearing the end of its useful life, see the Low battery warning section for details). Electrical/radio frequency
interference, obstructions, weather conditions and even sunspots can interrupt the signal from your remote to the system.The remote controls are the keys to
your system. But these remote controls are much more secure than car keys because each incorporates our ACG 2 (Anti-CodeGrabbing 2) technology with
trillions of digital codes for the ultimate protection against remote control cloning devices. You will use your ACE 7500 remote control to arm and disarm the
system, lock and unlock the doors, remotely start or shut down the engine, activate/deactivate the panic feature, enter/exit valet mode and command options
such as a remote trunk release, power window control, electric garage door interface, etc.
Re motely con trol ling your Clif ford system
TO ARM:
Press button 1 (master remote) or button (companion remote). Upon arming: two siren chirps, two parking
light flashes, dashboard LED flashes repeatedly and doors lock.
TO DIS ARM:
Press button 1 (master remote) or button (companion remote). Upon disarming: one chirp, one parking
light flash, LED turns off, doors unlock and the interior lights turn on.
TO ARM OR
DIS ARM SI LENTLY:
Simultaneously press button 3 (master remote) or both the button and the ✱ button
(companion remote) to arm or disarm without chirp acknowledgments.
TO PANIC:
For three seconds, continually press button 1 (master remote) or button (companion
remote). The parking lights will flash repeatedly and the siren will blare for 30 seconds. If the
ignition is on (indicating you are in the car), the doors will automatically lock to prevent an
assailant from entering (note: some vehicles are unable to lock the doors while the ignition is
on). If the ignition is off, the doors will unlock, allowing you to enter immediately without fumbling
with your keys.
TO RE MOTELY
OPEN THE TRUNK:
If you have this option, press button 2 (master remote) or button (companion remote) while the system is in its disarmed
state.
TO RE MOTELY
START THE EN GINE:
Press button 4 or button ✱ to remotely start the engine (or shut it down if idling under the system’s control). See Remote Engine
Starting DOs and DON’Ts for important information on this topic.
TO TURN VALET
MODE ON OR OFF:
Press the master remote LevelShift button twice, then button 1 or press both buttons ✱✱ and ✱ to enable/exit valet mode.
TO RE MOTELY OPEN
OR VENT WIN DOWS:
If you have this option, press the master remote LevelShift button once, then button 2 or press buttons and
(companion remote) after disarming to fully open the windows controlled by SmartWindows 4. On hot d ays, press this button
combination right after arming to vent the windows slightly while the system remains armed.
OTHER FEA TURES
AND OP TIONS:
Other system features and options can be accessed as noted in the following Quick Reference table:
4