Beltronics RX65 Radar Detector User Manual


 
Programming
12
There are 7 user-selectable options so you
can customize your RX65 for your own
preferences. The buttons labeled CITY and
BRT are also used to enter the Program
Mode, REVIEW your current program
settings, and to CHANGE any settings as
desired. The words PROGRAM, RVW, and
CHG are located on the top of the detector,
and are highlighted in colored graphics.
Pages 14-16 explain each option in more
detail.
How to use Programming
1 To enter Program Mode, press and
hold the CITY and BRT buttons for 2
seconds.
(The unit will beep twice, and
will display the word “Program”).
2 Then press the RVW button to
review the current settings
. (You can
either tap the button to change from item to
item, or hold the button to scroll through
the items).
3 Press the CHG button to change
any setting.
(You can either tap the button
to change from setting to setting, or hold
the button to scroll through all the options).
4 To leave the Program Mode, simply
wait 8 seconds without pressing any
button.
(The unit will display Complete,
beep 4 times, and return to normal
operation).
An example
Here is how you would turn RX65’s
AutoMute feature off.
1 Enter the Program Mode by holding
both the CITY and BRT buttons down for
2 seconds.
The RX65 will beep twice and
display
Program.
2 Then hold the RVW button down. The
RX65 will scroll through the categories,
starting with Pilot (
Pilot), then Voice
(
Voice), then Power-on sequence
(
PwrOn), then Signal strength meter
(
Meter), and then AutoMute (aMute).
3 Release the RVW button when RX65
shows the AutoMute item.
Since the factory
setting is for AutoMute to be on, RX65 will
display
aMute ON.
(If you accidentally don’t release the
RVW button in time, and the RX65 goes to
the next category, hold the RVW button
down again, and after RX65 scrolls
through all categories, it will begin again
at the top of the list.)
4 Press the CHG button to change from
aMute ON to aMute OFF.
5 To complete the Programming, simply
wait 8 seconds without pressing any button.
The RX65 will display Complete, beep 4
times, and return to normal operation.
Overview of Programming
13
Pilot HWY
Pilot H
Pilot V
Voice ON
Voice OFF
PwrOn STD
PwrOn FST
Meter STD
Meter THT
Meter TEC
aMute ON
aMute OFF
City STD
City LoX
City NoX
Bands ALL
Bands MOD
X ON or OFF
K ON or OFF
Ka USA or Intl or OFF
POP ON or OFF
Ku ON or OFF
LSR ON or OFF
SWS ON or OFF
Press the CHANGE button
to change your setting
within a category
*Full word: Highway or AutoScan or City
Letter: H or A or C
Vehicle voltage
*Voice alerts on
Voice alerts off
*Standard power-on sequence
Fast power-on sequence
*Standard signal strength meter
Threat Display
Tech Display
*AutoMute on
AutoMute off
*Standard City mode sensitivity
Low X band sensitivity in City Mode
No X band sensitivity in City Mode
*All bands enabled
One or more bands are disabled
Turn bands “ON” or “OFF” by
pressing the VOLUME/MUTE button
Press the REVIEW button
to go from one category
to the next
PILOT
(Power-on indication)
VOICE
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
CITY MODE SENSITIVITY
BANDS
* Factory Default Settings
To reset RX65 to its original factory
settings, press and hold the “CITY”
and “BRT” buttons while turning
the power on. The RX65’s display
will provide a “Reset” message,
accompanied by an audible alert,
acknowledging the reset.