Filter
Top Products
8
9
1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse
2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock
*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for Lock and Unlock
See setting 4 for door unlock and disarm output durations.
1 Ignition Lock & Unlock Enabled 1 Flash Doors Lock / Unlock when the key is turned On/ Off
2 Ignition Lock Only 2 Flashes Doors Lock when ignition key is turned ON only
*3 Ignition Auto Lock Disabled 3 Flashes Doors do not Lock or Unlock with the Ignition key
1 Lock & Unlock chirps Disabled 1 Flash Honks for Panic and Car Finder Mode only.
2 Lock & Unlock chirps Enabled 2 Flashes Honks for Lock, Unlock, Panic and Car Finder Mode Only.
*3 All Chirps Enabled 3 Flashes Honks for Lock, Unlock, Start, Panic and Car Finder.
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 1- Ignition Auto Lock
Setting 2- Horn Honk Settings
Setting 3- Door Lock Options
PROGRAM MODE 1 - USER SETTINGS
PROGRAM MODE 2 - ADDITIONAL SETTINGS
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm
2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release (3rd Ch)
3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm
1 5ms Pulsed Output 1 Flash Short (Quiet) Pulses
2 20ms Pulsed Output 2 Flashes Long (Loud) Pulses
*3 10ms Pulsed Output 3 Flashes Normal (Medium) Pulses
Setting 3 Horn Honk Timing
1 Secure Valet Active 1 Flash Valet only if ignition “ON” and Program Button is held for 15 seconds
2* Normal Valet Active 2 Flashes Valet if ignition “ON” and Program Button is held for 5 seconds
Setting 1 - Secure Valet Mode
Setting 2 - Parking Light Output
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
1 Short Pulses 1 Flash 125ms pulses with Unlock and on the disarm output.
2* Normal 2 Flashes 750ms pulses with Lock, Unlock and on disarm output.
Setting 4 - Door Unlock & Disarm Pulse Duration
Note: Programming this option will change the pulse length of this output from 750ms to 125ms.
1 Type 1 1 Flash Pulse after start and with lock
2 Type 2 2 Flashes Pulse after start only
3* Factory Re-arm 3 Flashes 0.75 second pulse with lock and after shutdown
Press the Program Button 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output- Yellow Wire on 14-Pin
1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated
2 45 Min Run Time 2 Flashes Remote Starter runs for 45min when activated
3* 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated
1 10 Seconds 1 Flash 10 sec Max time that starter will stay engaged
2 3 Seconds 2 Flashes 3 sec Max time that starter will stay engaged
3*5 seconds 3 Flashes 5 sec Max time that starter will stay engaged
1Active Starter Kill 1 Flash On when locked, Before ignition and 2 seconds after ignition turns off.
2Passive Starter Kill 2 Flashes Same as setting 1 but will arm 60sec after the ignition turns off.
3*Bypass Module 3 Flashes Output before ignition. Stays on 2 seconds after ignition turns off.
1 Safety ON 1 Flash Must press the start button twice to remote start the vehicle
2* Safety OFF 2 Flashes Press the start button once to remote start the vehicle.
Press the Program Button 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Press the Program Button 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Button. Press Program Button momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Starter Kill/ Bypass Module Output- Orange wire on 14-Pin Con.
Setting 7- Safety Start Mode
PROGRAM MODE 3 - STARTER SETTINGS
1 Type 1 1 Flash Unlock before start. Lock pulse after start and shutdown
2 Type 2 2 Flashes Lock pulse only after remote starter shuts off
3* Normal Operation 3 Flashes No additional re-lock pulses
Setting 1- Special Door Lock/ Unlock Operations
Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
Press the Program Button 2 time to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Button until you receive the appropriate # of park light flashes and horn honks.
Release the Program Button . Press momentarily to move to next program step or repeat to change selection.
1 Negative Input/ 30seconds 1 Flash Waits a maximum 30 seconds before starting.
2 Timed Delay/ 15 Seconds 2 Flashes Ignition ON for 15 seconds before engaging remote starter
3* Gas/ Positive Glow Plug 3 Flashes Waits 2 seconds to start if no diesel input is detected
Setting 2- Gas/ Diesel Mode- Blue Wire on 14-Pin