Filter
Top Products
Installation Guide
Installation Guide
OPERATIONS
10
OTHER FEATURES
Step 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON
Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park-lights do not come
on at this point, turn key off for 5 seconds, then repeat step 1.
Step 3 - Continue to hold the Program Switch, the park lights go out. (Do not release Program Button)
Step 4 - Press the LOCK button on each of 1st car remote’s and press the # button on each of the 2nd
car remote’s of the transmitters to be programmed. The park lights will flash once and the
horn will honk once each time a new code is learned.
Note: Transmitter programming must done quickly. Do not pause more than one second between each
transmitter. All the transmitters to be used must be programmed at the same time. All transmitters
not programmed at this time will be erased from memory for security. The system holds a
maximum of 4 transmitter codes including 2nd car remote codes.
You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a
second vehicle.
ACTIVATING Service Mode
1. While the ignition is “ON” press and hold the Program Button for five seconds. The
park lights will flash five times and the horn (optional)will honk five times to confirm
that the system is in Service Mode.
2. While in Service Mode the remote start functions will be disabled and LED’s will be
“ON” steady. Door locks and trunk release are still operational.
DEACTIVATING Service Mode
1. While the ignition is “ON” press and hold the Program Button for five seconds. The
park lights will flash two times and the horn (optional)will honk two times to confirm
that the system has exited Service Mode.
2. Remote start functions will return to normal operation.
+
-
Step #1 Step #2
Step #3 Step #4
Carefully remove the
screw from back of
the remote.
Remove top case
then replace the
battery.
Replace top case.
Re-install screw.
Test remote for
proper operation.
The transmitter battery should be changed at least once every year to maintain proper operating range.
Replace with quality23A 12volt Alkaline battery.
Transmitter Programming
System Service Mode
System Service Mode - By Remote
Battery Replacement
ACTIVATE Service Mode
1 - Press and Release button #4 then press and hold Button #4 again for 6
seconds until Status LED comes on Steady
NOTE: If horn is connected the horn will honk 5 times.
DEACTIVATE Service Mode
1 - Press and Release button #4 then press and hold Button #4 again for 6
seconds until Status LED turn off.
NOTE: If horn is connected the horn will honk 2 times.
11
PROGRAM MODE 4 - TACH SETTINGS
Setting 1- Method 2- Low Idle Learn
Setting 1- Auto Tach Learn.
Setting 2- Adjust For Over-Crank
Setting 3- Adjust For Under-Crank
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program Button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press the # button on the remote.(Button #4).
Step 3 - Start Vehicle - Using the ignition key, make sure not to turn the key off at any time or your will exit programming.
Step 4 - Press the Button - One time (Led will start flashing in single cycles) then press and hold Program Button for(5sec).
Step 5 - Release the Button - Led should come on steady to indicate correct tach signal the park light will flash to confirm.
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Menu 4 - Press the # button on the remote.(Button #4).
Step 3 - Press the Program Button - 2 times (Led will start flashing 2 times).
Step 4 - Hold the Program Button - For 5 seconds until park lights flash (each time lights flash the setting is reduced).
Step 5 - Release the Button - Exit Program Mode and remote start to test.
Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Step 2 - Enter Program Mode 4 - Press the # on the remote.(Button #4).
Step 3 - Press the Program Button - 3 times (Led will start flashing 3 times).
Step 4 - Press and Hold Program - For 5 seconds until park lights flash (each time lights flash the setting is increased).
Step 5 - Release Program - Exit Program Mode then remote start to test.
This option is used for vehicles that maintain a High or Erratic idle after starting and need more than 10
seconds to establish a stable idle.
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected.
Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be
bypassed during the activation of the remote starter. Never disconnect or alter the switch to be always
bypassed. Always use a “M” Series Remote Starter on a manual transmission vehicle.
Never install a automatic Remote Starter model into a manual transmission vehicle. It is not
recommended to install a remote starter on a convertible type vehicle. If doing so It is highly
recommended that a radar sensor is installed to cover the proximity of the gear shift lever. If the radar
sensor is tripped the remote starter will exit Reservation Mode.
To enter Reservation Mode, the following steps must be followed.
Step 1 - While the vehicle is running, place the transmission in neutral and apply the parking brake.
Step 2 - Press and release the brake pedal. The park lights will flash.
Step 3 - Turn the ignition key off and the vehicle will stay running.
Step 4 - Exit the vehicle and close the door. The vehicle will then shut off.
Step 5 - The vehicle can now be safely remote started.
NOTE: If the vehicle has a dome light delay, the vehicle may stay running until the dome light turns off.
This is normally no longer than 30 seconds. Reservation Mode will automatically be exited if the doors
of the vehicle are opened. The set-up mode will then have to be repeated . Reservation Mode Must
Be set-up each time the vehicle is parked.
Reservation Mode - Manual Transmissions Only.
1) Make all the required wire connections and plug-in the Unit.
**The park lights should flash twice upon power up.
2) Turn the Ignition Key ON. (Park Lights will turn on).
3) Start the vehicle, LED’s on antenna will come when proper tach signal is detected**, then after 30-35
seconds the park lights will turn off then flash twice to confirm tach learning.
Note: A system reset must be done before a new tach signal can be learned to the module.