Filter
Top Products
SYSTEM PROGRAMMING - Menu 1
PAGE 20
INSTALL MANUAL
PROGRAM MODE
CON'T FROM PREVIOUS PAGE
CHANGE SETTING 4 -
GOTO SETTING 5 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 4- RE-ARM OPTIONS
THE HORN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED
4 CHIRPS
PRESS
1 TIME
4X
1 CHIRP
2 CHIRPS
3 CHIRPS
CHANGE SETTING 5 -
GOTO SETTING 6 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 5- RUN TIME
THE HORN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED
5 CHIRPS
PRESS
1 TIME
5X
1 CHIRP
2 CHIRPS
3 CHIRPS
SETS OPTION 1 – 4 MINUTES- The system will run for approximately 4 minutes
then shut off.
SETS OPTION 2 – 45 MINUTES- The system will run for approximately 45 minutes
then shut off.
SETS OPTION 3 – 15 MINUTES- The system will run for approximately 15
minutes then shut off. (DEFAULT)
SETS OPTION 1 - TYPE 2- The rearm output pulses only when the lock button is
pressed.
SETS OPTION 2 – AFTER START- The re-arm output will pulse after the remote
start starts the vehicle (DEFROST/ HEATED SEAT)
SETS OPTION 3 – REARM- Pulsed output when the doors are locked and after
remote start shutdown. (DEFAULT)
72 SERIES
1 CHIRP
SETTING 3- (+) GLOW PLUG/ INPUT TRIGGER TO START
THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED
3 CHIRP
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
2 CHIRP
3 CHIRP
SETS OPTION 1 – NEGATIVE GLOW PLUG/ 20 SECOND DELAY START
SETS OPTION 2 – POSITIVE TRIGGER TO START (1 PULSE)- 1 (+) pulse on the
input will activate remote starter.
SETS OPTION 3 – GAS ENGINE/ POSITIVE GLOW PLUG
SYSTEM PROGRAMMING - Menu 1
PAGE 21
INSTALL MANUAL
PROGRAM MODE
ENTERING PROGRAM MODE 4
72 SERIES
1 CHIRP
CHANGE SETTING 1 -
GOTO SETTING 2 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 1- TACH OPTIONS
THE HORN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED
1 CHIRP
PRESS
1 TIME
1X
CHANGE SETTING 2 -
GOTO SETTING 3 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 2-ADJUST FOR UNDER-CRANK
THE HORN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED
2 CHIRPS
PRESS
1 TIME
2X
1 CHIRP
1 CHIRP
2 CHIRPS
Each time the HORN chirps the Tach setting is reduced by 10%
SETS OPTION 1 – 300ms- The system will wait 300ms before starting to monitor the
Tach input.
SETS OPTION 1 – HYBRID 1- The remote starter will ignore the Tach input after the
remote start activates.
SETS OPTION 2 –HYBRID 2- No Tach connection required. Starter wire defaults at 2
seconds.
Each time the HORN chirps the Tach setting is increased by 10%
SETS OPTION 2 – 750ms- The system will wait 750ms before starting to monitor the
Tach input.
SETS OPTION 3 – NO WAIT- The system will monitor the Tach as soon as the
vehicle has remote started. (DEFAULT)
1 CHIRP
2 CHIRPS
3 CHIRPS
CHANGE SETTING 4 -
GOTO SETTING 1 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 4- TACH WAIT
THE HORN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED
4 CHIRPS
PRESS
1 TIME
4X
1 CHIRP
1 CHIRP
CHANGE SETTING 3 -
GOTO SETTING 4 - PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE HORN CHIRP(S)
SETTING 3-ADJUST FOR OVER-CRANK
THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED
3 CHIRPS
PRESS
1 TIME
3X
1 CHIRP
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
HORN CHIRP
Press #
Button to
Select Menu 4
REMOTE BUTTON
2 CHIRPS
SETS OPTION 3 –AUTO TACH LEARN- The system will automatically learns the
vehicles Tach. Tachless on TL Models. (DEFAULT)