A SERVICE OF

logo

Open as PDF
next previous
35EN
EnglishFrançaisEspañol
Weakchannelinstallation
This function lets you add the channels that were not added by the
autoprogram due to the receptible condition at the initial setup.
1 Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [Channels] > [Weakchannel
installation].
2 Use
Í
/
Æ 
to select
 
channel input box, then use
Î
/
ï
to select a
channel you want to memorize.
3 Use
Í
/
Æ 
to select [Search], then press OK.
4 Display will be changed to [Store] from [Search] when the channel
is found, then press OK.
5 Press MENU to exit.
Note
•
In most cases, digital channels are not broadcast on the RF channel on which they
appear on your TV. To add digital channels you need to know the RF channel on which
the digital channel is being broadcast. E.g. If there is a digital channel 9.1 which is being
broadcast on RF channel 25, you need to enter 25 while performing a weak channel
installation. To nd out the RF channel on which a particular digital channel is being
broadcast, please contact your local service provider.
Installing digital channels using [Weakchannelinstallation] might not work for direct
cable connections and if the digital signal is too weak for the TV to process.
Installationmode
1
Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [Channels] > [Installationmode].
2 Use
Î
/
ï 
to select, then press OK.
3 Press MENU to exit.
Uninstallchannels
Those channels can still be selected with theNumberbuttons.
1 Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [Channels] > [Uninstallchannels].
2 Use
Î
/
ï
 
to select the channel you want to remove, then press OK.
• You will not be able to select the channel again using CH+/−.
• To reactivate a removed channel, use
Î
/
ï
and then press OK.
3 Press MENU to exit.
Returnyoursettingstodefaultvalues
When you return picture and sound settings to their default values the
channel installation settings are not affected.
1 Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [ResetAVsettings] > [Startnow].
2 Press OK to reset the picture and sound settings.
3 Press MENU to exit.
7 Installchannels
The rst time you set up your TV, you are prompted to select a menu
language and to install TV and digital radio channels (if available). This
chapter provides instructions on how to reinstall and ne-tune channels.
Selectingyourmenulanguage
1
Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [Language].
Picture
Sound
Features
Installation
Software
Language
Channels
Preferences
Network
Clock
Reset AV settings
English
Français
Español
2 Select a language and then press OK to conrm your choice.
3 Press MENU to exit.
Autoprogram
If you switch wires (e.g., between antenna and CATV) or if you move
the unit to a different area after the initial setting, you will need to
perform autoprogram.
1 Press MENU on the remote control and then use
Î
/
ï
/
Í
/
Æ
to
select [Setup] > [Installation] > [Channels] > [Autoprogram] >
[Startnow].
System searching. Please wait...
Digital channels found: 0
Analog channels found: 0
Auto programming may take more than
20 minutes to complete.
Stop
2 Press OK to start the installation.
If you run [Autoprogram] when you have locked channels, a
message appears asking to enter your PIN . Enter your PIN in order
to complete the installation.
If you have forgotten your PIN, reset it as described in ‘Changing
your PIN’ on page 26.
• When autoprogramming is complete, the lowest memorized
channel will be displayed.
3 Follow the on-screen instructions to complete the installation.